ARM V2M-Juno r2 Technical Reference Manual Download Page 77

Page: 77 / 150

3.5

Use of reset push buttons

The ON/OFF/Soft Reset button performs a software reset of the system, and the Hardware Reset button
performs a hardware reset of the system.

This section contains the following subsections:
•

3.5.1 Use of ON/OFF/Soft Reset button

on page 3-77

•

3.5.2 Use of Hardware Reset button

on page 3-77

3.5.1

Use of ON/OFF/Soft Reset button

This push button enables you to perform a software reset of the system.

You initiate a software reset of the system by briefly pressing the

ON/OFF/Soft Reset

button during run

time. The MCC performs a software reset of the Juno r2 SoC and resets the devices on the board.

The software reset sequence is as follows:
1. Briefly press the

ON/OFF/Soft Reset

button.

Caution

If you press and hold the

ON/OFF/Soft Reset

button for more than two seconds, the system enters the

standby-state in the same way as pressing the

Hardware Reset

button.

2. The MCC asserts the

CB_nRST

reset signal.

3. The MCC releases

CB_nPOR

4. The MCC releases

CB_nRST

5. The V2M-Juno r2 motherboard enters the operating-state.

Note

• The MCC does not read the configuration files or perform a board reconfiguration as a result of a

software reset.

• The

CB_nPOR

signal drives the

nPORESET

signal inside the Juno r2 SoC.

Related concepts

2.6.1 Reset push buttons

on page 2-35

Related references

1.3 Location of components on the V2M-Juno r2 motherboard

on page 1-15

1.4 Connectors on front and rear panels

on page 1-16

3.5.2

Use of Hardware Reset button

This push button enables you to perform a hardware reset of the system.

You can change the operation of the board from the operating-state to the standby-state by briefly
pressing the

Hardware Reset

button. This switches off the power to the board and resets the system to the

default values.

If you then press the

ON/OFF/Soft Reset

push button, the system performs a full configuration and enters

the operating-state.

Related concepts

2.6.1 Reset push buttons

on page 2-35

Related references

1.3 Location of components on the V2M-Juno r2 motherboard

on page 1-15

1.4 Connectors on front and rear panels

on page 1-16

3 Configuration

3.5 Use of reset push buttons

ARM 100114_0200_03_en

3-77

Non-Confidential

Summary of Contents for V2M-Juno r2






















































































































































Search results

Summary of Contents for V2M-Juno r2

Reviews:

Related manuals for V2M-Juno r2

Brands by name

Popular brands

ARM V2M-Juno r2, Technical Reference Manual

Search results

Summary of Contents for V2M-Juno r2

Reviews:

Related manuals for V2M-Juno r2

Brands by name

Popular brands