manualshive.com logo in svg

ARM V2M-Juno r2, Technical Reference Manual

Share
Download
ARM V2M-Juno r2 Technical Reference Manual Download Page 69

The sleep-state to operating-state sequence is as follows:
1. A short press of the 

On/Off/Soft Reset

 button, less than two seconds.

2. The 

System Control Processor

 (SCP) enables the Cortex-A72, Cortex-A53, VSYS, and the

Mali-T624 GPU.

3. The SCP performs basic Juno r2 SoC setup, PLLs, internal clocks, and test chip peripherals.
4. The SCP writes state data to on-chip secure RAM so that the application cluster, that is, either the

Cortex-A72 or Cortex-A53, resumes in the correct state and does not boot up from standby.

5. The SCP releases the 

Power Policy Unit

 (PPU) to start the application cluster boot sequence.

6. The application code resumes from the point when the Juno r2 SoC went into the sleep-state.

3 Configuration

3.2 Configuration process and operating modes

ARM 100114_0200_03_en

Copyright © 2015–2017 ARM Limited or its affiliates. All rights reserved.

3-69

Non-Confidential

Summary of Contents for V2M-Juno r2























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands