ARM V2M-Juno r2 Technical Reference Manual Download Page 68 | Manualshive

Page: 68 / 150

background image

• Pressing the

Hardware Reset

button.

• Pressing and holding the

On/Off Soft Reset

button for more than two seconds.

• A powerdown request from the operating system.

2. The

System Control Processor

(SCP) signals a powerdown request to the application cluster, that is,

either the Cortex-A72 cluster or the Cortex-A53 cluster.

3. The application cluster goes through its cleanup and shutdown sequence.
4. The application cluster goes to the

Wait for Interrupt

(WFI) state.

5. The

Power Policy Unit

(PPU) sees the WFI state and powers down.

Note

The SCP waits for this sequence to complete.

6. The SCP powers down the Cortex-A53, Cortex-A72, VSYS, and Mali-T624 GPU.
7. The SCP signals to the MCC, using the

Power Management IC

(PMIC),

Ready for Shutdown

.

8. The MCC applies

CB_nPOR

and disables the board clocks and the PMIC.

Note

The

CB_nPOR

signal drives the

nPORESET

signal inside the Juno r2 SoC.

9. The V2M-Juno r2 motherboard is in the standby-state until pressing the

On/Off/Soft Reset

button

initiates the powerup and configuration sequence.

3.2.4

Sleep-state sequence

The sleep-state is a low power mode of the Juno r2 SoC that preserves operating data and the application
code state. The sleep-mode sequence takes the Juno r2 SoC from the operating-state to the sleep-state.

The operating-state to sleep-state sequence is as follows:
1. A short press of the

On/Off/Soft Reset

button, less than two seconds.

Warning

Pressing and holding the

On/Off/Soft Reset

button for more than two seconds initiates the powerdown

sequence and puts the V2M-Juno r2 motherboard into the standby-state. This might result in loss of
data.

2. The

System Control Processor

(SCP) sends the

Message Handling Unit

(MHU) sleep command to

the application cluster, that is, either the Cortex-A72 or Cortex-A53.

3. The application cluster goes through its cleanup and shutdown sequence. The application cluster goes

to the

Wait for Interrupt

(WFI) state.

4. The

Power Policy Unit

(PPU) sees the WFI state and powers down.

Note

The SCP waits for this sequence to complete.

5. The SCP powers down the Cortex-A53, Cortex-A72, VSYS, and Mali-T624 GPU.
6. The SCP maintains on-chip RAM and secure RAM data. This data is available when the Juno r2 SoC

returns to the operating-state.

7. The Juno r2 SoC is in the sleep-state until a short press, less than two seconds, of the

On/Off/Soft

Reset

button initiates the wake up sequence and returns it to the operating-state.

3.2.5

Wake-up sequence

The wake-up sequence takes the Juno r2 SoC from the sleep-state to the operating-state. Application
software resumes operation from the previous operating point with all data restored.

3 Configuration

3.2 Configuration process and operating modes

ARM 100114_0200_03_en

Copyright © 2015–2017 ARM Limited or its affiliates. All rights reserved.

3-68

Non-Confidential

«
...
66
67
68
69
70
...
»

Summary of Contents for V2M-Juno r2























































































































































Reviews:

No comments

Related manuals for V2M-Juno r2

Brand: Actel Pages: 2

Brand: Intel Pages: 80

Brand: ECS Pages: 60

DS-5116HFI Series

Brand: HIKVISION Pages: 22

Brand: BCM Pages: 5

MEG X570S UNIFY-X MAX

Brand: MSI Pages: 204

Brand: H-Tec Pages: 28

Brand: ASROCK Pages: 18

Brand: ASROCK Pages: 257

X570S AORUS PRO AX

Brand: Gigabyte Pages: 52

8A 72QFN Series

Brand: IDT Pages: 29

Brand: Acrosser Technology Pages: 3

Brand: BESTEK Pages: 13

Brand: Linear Technology Pages: 6

Brand: Microchip Technology Pages: 30

Gamefisher 298.586180

Brand: Gamefisher Pages: 23

Brand: IDT Pages: 5

Brand: Aaeon Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands