Ariterm Arimatic 151 User Manual Download Page 9

Page: 9 / 43

v2.00

Ariterm Oy

21.5.2013

- Burner mode (EFFECT MODE,UPKEEP, MANUAL, STOP)

- Boiler water temperature

- Effect percentage at which the burner is currently run

- Primary and secondary fan power

- Smoke gas fan power

- Operation of burner screw

- Operation of storage auger

- Funnel surface level sensor status

- Flame detection information

- Underpressure of combustion chambers

- Residual oxygen (if option is activated)

- Burner screw temperature (if option is activated)

- Bar discharger (if option is activated)

- Silo lower limit (if option is activated)

- Time and date.

System settings cannot be adjusted on the

MAINPAGE

. Settings can be

adjusted on the

OPERATION

-page.

7.2

ALARMS

-page

Figure 2. ALARMS -page

Alarms are indicated with a red blinking light appearing on the display and the
system goes into

Stop

-mode. The

ALARMS

page displays active alarms

Summary of Contents for Arimatic 151












































Search results

Summary of Contents for Arimatic 151

Reviews:

Related manuals for Arimatic 151

Brands by name

Popular brands

Ariterm Arimatic 151, User Manual

Search results

Summary of Contents for Arimatic 151

Reviews:

Related manuals for Arimatic 151

Brands by name

Popular brands