manualshive.com logo in svg

Ariterm Arimatic 151, User Manual

Share
Download
Ariterm Arimatic 151 User Manual Download Page 28

v2.00 

Ariterm Oy 

21.5.2013 

27 

 

15.

 

Storage auger settings 

 

 

Figure 15. STORAGE AUGER settings 

 

Setting 

Factory 
setting 

Setting 
frequency 

Function 

Funnel's emptying time 

15s 

0-60s 

When the funnel photocell pair no 
longer detects fuel in the funnel, 
the total operating pulse time of the 
burner screw is calculated. When 
the set time is reached, the storage 
auger is activated. The settings 
define the lower limit of the funnel. 
When the photocell pair detects 
fuel, the storage auger stops. 

Storage alarm time delay 

600s 

0-1200s 

When the storage auger has run 
for the set time, but the funnel 
photocell pair fails to detect the 
surface of the fuel, the system 
indicates the 

Alarm!

 

Fuel low

 

alarm. 

Inactive sensor level for 
burner screw 

150s 

0-600s 

If the funnel photocell pair detects 
fuel during the set time (calculated 
with the feeder auger pulses), the 
storage auger is activated for the 
set duration. The purpose here is 
to remove any splinters blocking 
the sensor. NOTE! Settings are 
displayed if the bar discharger 
option was selected. 

Funnel's force filling 
time 

2s 

0-60s 

Storage auger running time after 
the forced filling delay. 

 

Summary of Contents for Arimatic 151












































Reviews:

No comments

Brands by name

Popular brands

Load more brands