AREMDE NEXUS User Manual Download Page 58 | Manualshive

Page: 58 / 80

background image

58

9.0 CLEANING NEXUS/STYLUS

Group Heads

- Refer to section 6.2 AUTO CLEAN CYCLE on how to clean group heads using automatic cleaning function.

Shower Screens

- Loosen shower screen and remove screw/bolt.
- Remove the shower screen and attached diffuser. Take care when removing as surface will be HOT.
- Clean with soapy water (Cafetto cleaner supplied in accessories kit). Rinse with clean fresh water to
remove soapy residue.
- Screw back into the group. Take care to not over tighten as the screw could break off inside group head.

It is imperative that ONLY approved cleaning TABLETS be used in the Nexus/

Stylus. These can be ordered through [email protected]. Item #NX00339.

Please take care when removing the group showers - HOT SURFACE. Wide blade

flathead screwdriver is required. Do not over tighten, never leave out overnight.

9.1 Operator Surfaces

-

«
...
56
57
58
59
60
...
»

Summary of Contents for NEXUS

















































































Reviews:

No comments

Related manuals for NEXUS

STILISTA PRIMEO

Brand: Martello Pages: 20

Brand: Guzzanti Pages: 63

Caf 3 in 1 Coffee Maker KDC120

Brand: Kambrook Pages: 10

Brand: Beper Pages: 44

Brand: Saeco Pages: 47

EGRO ONE Top Milk

Brand: Egro Pages: 2

Brand: iGenix Pages: 12

Espresso AC-755

Brand: Aircraft Pages: 9

Brand: Bella Pages: 24

Brand: Russell Hobbs Pages: 45

Brand: U-Line Pages: 20

Brand: Galanz Pages: 7

BARISTA AROMA SOLO

Brand: STARBUCKS Pages: 40

Brand: Hamilton Beach Pages: 14

Brand: Rancilio Pages: 30

Brand: Bodum Pages: 20

Brand: Bodum Pages: 39

Brand: Nevir Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands