ARB 3414470 Fitting Instructions Manual Download Page 1

Page: 1 / 18

Last Rev Date: 07/11/12

Page 1 of 18

Fitting instructions# 3787907

Part Number:

3414470 F/ Kit 6173258, Winch F/Kit 3514010

Product Desc:

HILUX ARB COMMERCIAL BULL BAR 2005 ONWARDS
INCLUDING 2011 UPDATE.

Suited to
vehicle/s:

4 x 4 Flared and Non Flared (SRS AIR BAG MODELS)

Not suitable for 2WD (4 x 2) models

NOTE: Optional winch kit 3514010

Optional wing underpanel kit 3514070

WARNING

REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG;

When installed in accordance with these instructions, the front protection bar does not affect operation of
the SRS airbag.

ALSO, NOTE THE FOLLOWING:

♦

This product must be installed exactly as per these instructions using only the hardware supplied.

♦

In the event of damage to any bull bar component, contact your nearest authorised ARB stockist. Repairs or

modifications to the impact absorption system must not be attempted.

♦

Do not use this product for any vehicle make or model, other than those specified by ARB.

♦

Do not remove labels from this bull bar.

♦

This product or its fixing must not be modified in any way.

♦

The installation of this product may require the use of specialized tools and/or techniques

♦

It is recommended that this product is only installed by trained personnel

♦

These instructions are correct as at the publication date. ARB Corporation Ltd. cannot be held responsible

for the impact of any changes subsequently made by the vehicle manufacturer

♦

During installation, it is the duty of the installer to check correct operation/clearances of all components

♦

Work safely at all times

♦

Unless otherwise instructed, tighten fasteners to specified torque

ARB 4x4 ACCESSORIES

Corporate Head Office

42-44 Garden St

Tel:

+61 (3) 9761 6622

Kilsyth, Victoria

Fax:

+61 (3) 9761 6807

AUSTRALIA 3137

Australian enquiries

[email protected]

North & South American enquiries

[email protected]

Other international enquiries

[email protected]

www.arb.com.au

Summary of Contents for 3414470



















Search results

Summary of Contents for 3414470

Reviews:

Related manuals for 3414470

Brands by name

Popular brands

ARB 3414470, Fitting Instructions Manual

Search results

Summary of Contents for 3414470

Reviews:

Related manuals for 3414470

Brands by name

Popular brands