ARB 3414470 Fitting Instructions Manual Download Page 3 | Manualshive

Page: 3 / 18

background image

Last Rev Date: 07/11/12

Page 3 of 18

Fitting instructions# 3787907

Copyright © 2005 by ARB Corporation Limited. All rights reserved, this document must not be reproduced without the express authority of ARB Corporation Ltd

PARTS LISTING

APPLICATION.

PART NO.

QTY

DESCRIPTION

**CONTROL BOX FITMENT

(SUPPLIMENTARY KIT )

3756499
6151234
4581045
6151132

EG50

180302

1
2
2
2
2
8

CONTROL BOX BRACKET
BOLT M8 x 25 LONG (BLACK)
WASHER FLAT M8 (BLACK)
NUT FLANGE M8
GROMMET RUBBER
CABLE TIES

**WINCH MOUNT

(SUPPLIMENTARY KIT)

4581040
6151074

BLB850

4
2
3

WASHER FLAT 3/8”
BOLT UNC 3/8” x 1 ¾”
CABLE BLACK 850mm

BOLT BULL BAR TO MOUNTS

6151428
6151355
4581049
4581064

6
6
6
6

NUT FLANGE M12
BOLT M12
WASHER FLAT M12
WASHER SPRING M12

BULL BAR PINNING

6151357
6151321

2
2

BOLT (SEMS) M10
NUT FLANGE M10

IMP. ABS. TO CHASSIS

3757766R

3757766L

3194068R

3194068L

4581288
6151357
6151133
6151026
4581008
6151232
4581040
4581048
6151095
4581064
4581007

1
1
1
1
4
2
4
4
2
2
4
6
2
2
2

MOUNT BRACKET ASSY R.H.S
MOUNT BRACKET ASSY L.H.S
MOUNT BRACE R.H.S
MOUNT BRACE L.H.S
WASHER FLAT M10 (OVERSIZED)
BOLT (SEMS) M10
NUT M10 X1.25P FINE THREAD
NUT M10 X1.5P
WASHER OFFSET 40 X 13
BOLT M10 x 30 x 1.5mm
WASHER FLAT M10 X 25mm
WASHER SPRING M10
BOLT M12 X 1.25 X 30 FINE THREAD
WASHER SPRING M12
WASHER FLAT LG M12 X 4mm THK

STONE TRAY

6522719
6151234
6151303
4581045
4581047

1
6
6
6
6

STONE TRAY
BOLT M8
NUT CAGE M8
WASHER FLAT M8
WASHER SPRING M8

INDICATORS TO BULL BAR

6821151R

1

INDICATOR KIT, RHS

6821151L

1

INDICATOR KIT, LHS

6821116

4

NYLON PLUG

6151308

4

SCREW, SELF TAPPING

6821152

2

WIRING LOOM

6821198

1

INDICATOR RELAY LOOM

1080302

6

CABLE TIES

NUMBER PLATE

6151017
6151300
4581072
4581036

2
2
2
2

BOLT M6
NUT CAGE M6
WASHER FLAT M6
WASHER SPRING M6

MISCELLANEOUS

6191026
3787817
3787818
3787979
3787980
6151338

1
1
1
1
1
2

PINCH WELD @ 2700MM
CUTTING TEMPLATE NON FLARED 05-11
CUTTING TEMPLATE FLARED 05-11
CUTTING TEMPLATE FLARED 11on
CUTTING TEMPLATE NON FLARED 11on
SCREW PAN HD PLASTITE

**NOTE: GREY FILLED ITEMS LISTED ARE AVAILABLE ONLY IN SUPPLIMENTARY WINCH FITTING KIT
3514010, THEY DO NOT COME IN STANDARD KIT.
NOTE IF FITTING AN XDC WINCH, SUPPLIMENTARY KIT 3500140 CONTROL BOX BRACKET IS REQUIRED

«
1
2
3
4
5
...
»

Summary of Contents for 3414470



















Reviews:

No comments

Related manuals for 3414470

Event Master E2

Brand: Barco Pages: 2

Brand: Barco Pages: 7

Brand: Barco Pages: 7

Titanium Series

Brand: Fass Pages: 13

Brand: Tailfin Pages: 8

Brand: SALSA Pages: 2

BEA LZR-WIDESCAN

Brand: Halma Pages: 12

Brand: U-Line Pages: 3

Brand: Fisher-Price Pages: 8

Brand: Whispbar Pages: 15

Brand: Cerlic Pages: 20

Brand: Safe Fleet Pages: 38

Brand: Stiebel Pages: 23

ecoCRAFT VKK GB 1206/3-E-H

Brand: Vaillant Pages: 48

Brand: DrBrowns Pages: 2

Brand: ESAB Pages: 12

Brand: Orno Pages: 4

Monitor _QSG_DE01

Brand: M-Audio Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands