ARB 3414470 Fitting Instructions Manual Download Page 16

Page: 16 / 18

Last Rev Date: 07/11/12

Page 16 of 18

Fitting instructions# 3787907

FITTING BULL BAR

72.

Once satisfied with the position of the
bull-bar, using a 10mm drill, drill
through the 10mm holes in the impact
absorber

73.

Drill 1 hole per side, and secure using
the M10 x 30 SEMS bolts and flange
nut.

74.

Fit the centre stone guard as shown
using M8 black bolts, black M8 flat
washers, black M8 spring washers &
cage nuts.

75.

Cable tie the plastic wheel liner on the
LH and RH side of the vehicle to the
hole provided in the wing.

76.

If fitting wing under panels proceed
now. Separate fitting instructions
are included with supplementary kit
3514050.

77.

Carefully cut the lower part of the
plastic wheel liner that hangs below the
wing stone guard with a pair of scissors
or sharp knife.

Summary of Contents for 3414470



















Search results

Summary of Contents for 3414470

Reviews:

Related manuals for 3414470

Brands by name

Popular brands

ARB 3414470, Fitting Instructions Manual

Search results

Summary of Contents for 3414470

Reviews:

Related manuals for 3414470

Brands by name

Popular brands