ARAG Bravo 180S Series Installation, Use And Maintenance Handbook Download Page 7

Page: 7 / 42

POSITION ON FARMING MACHINE

7.1

System recommended composition

ASSEMBLY DIAGRAM FOR SPRAYER WITH DIAPHRAGM PUMP

SYSTEM WITH MAIN VALVE

INTENDED APPLICATIONS

Fig. 3

Legend:

Monitor

Battery

GPS receiver (optional)

Filling pump

Flowmeter

External general control /
external speed sensor

Level sensor

Pressure sensor

Foam marker
(crop spraying only)

Speed sensor

Control valve

Main valve

1÷5

Section valves

Hydraulic unit

ASSEMBLY DIAGRAM FOR SPRAYER WITH DIAPHRAGM PUMP

SYSTEM WITH DRAIN VALVE

INTENDED APPLICATIONS

Fig. 4

Legend:

Monitor

Battery

GPS receiver (optional)

Filling pump

Flowmeter

External general control /
external speed sensor

Level sensor

Pressure sensor

Foam marker
(crop spraying only)

Speed sensor

Control valve

Main valve

1÷4

Section valves

Hydraulic unit

The computer must be directly connected to the farming machine battery.
* Do not connect the computer to key-operated switch (15/54).

CONTINUES

INSTALLATION

Summary of Contents for Bravo 180S Series











































Search results

Summary of Contents for Bravo 180S Series

Reviews:

Related manuals for Bravo 180S Series

Brands by name

Popular brands

ARAG Bravo 180S Series, Installation, Use And Maintenance Handbook

Search results

Summary of Contents for Bravo 180S Series

Reviews:

Related manuals for Bravo 180S Series

Brands by name

Popular brands