manualshive.com logo in svg

APS Resource HTC Kit, Installation And Owner'S Manual

Share
Download
APS Resource HTC Kit Installation And Owner'S Manual Download Page 21

PAGE 20

©2010 4Front Engineered Solutions, Inc. - APS Resource 

    

             

AP4047 RA 11/10

            

MAINTENANCE

Be  certain,  before  climbing  into  the  dock  leveler  pit 

or  doing  any  maintenance  or  repair  under  the  dock 

leveler, that: 1) THE MAINTENANCE STRUT AND LIP 

LOCK ARE SECURELY IN PLACE and 2) the power is 

disconnected and properly tagged or locked off.

Before servicing the dock leveler, read and follow the 

Safety  Practices  and  the  Operation  section  of  this 

manual.

Place  barricades  on  the  dock  floor  around  the  dock 

leveler pit and in the driveway in front of the pit while 

installing, maintaining or repairing the dock leveler.

Check all labels every 90 days. See parts list for location 

and part numbers. Replace if required.

Every 90 days inspect dock bumpers. Four inches (4") of 

bumper protection is required. Worn, torn, loose or missing 

bumpers must be replaced.

HYDRAuLIC FLuID LEVEL

The  hydraulic  fluid  level  should  be  checked  when  the 

leveler  is  resting  on  the  maintenance  post  with  the  lip 

pendant.  Reference Figure 28.

*Acceptable Hydraulic Oils:

1.  Mobil Aero HFA (49011)

2.  Exxon univis Grade JI3

3.  Texaco Aircraft Oil #1554

4.  u.s. Oil Co.,Inc. #ZFI-5606 (Low Temp.)

Summary of Contents for HTC Kit





























Reviews:

No comments

Brands by name

Popular brands

Load more brands