APS Resource HTC Kit Installation And Owner'S Manual Download Page 2

Page: 2 / 28

PAGE 1

AP4047 RA 11/10

LIMITED WARRANTY

APS Resource warrants that this HYDRAULIC CONVERSION KIT will be free from defects in material and workman-

ship under normal use for a period of one (1) year from the earlier of 1) 60 days after the date of initial shipment by

APS Resource, or 2) the date of installation of the HYDRAULIC CONVERSION KIT by the original purchaser, provided

that the owner maintains and operates the HYDRAULIC CONVERSION KIT in accordance with this Owner’s Manual.

In the event that this HYDRAULIC CONVERSION KIT proves defective in material or workmanship within the

applicable limited warranty period, APS Resource will, at its option:

1. Replace the HYDRAULIC CONVERSION KIT or the defective portion without charge to the owner, or

2. Alter or repair the HYDRAULIC CONVERSION KIT on site or elsewhere, without charge to the owner.

The limited warranty stated in the preceding paragraph IS EXCLUSIVE AND IT IS IN LIEU OF ANY OTHER

GUARANTEES AND WARRANTIES, EXPRESS OR IMPLIED. The limited warranty does not cover any failure

caused by improper installation, abuse, negligence or failure to maintain and adjust the Hydraulic Conversion Kit

properly. Parts requiring replacement due to damage resulting from vehicle impact, abuse or improper operation are

not covered by this warranty. APS Resource disclaims any responsibility or liability for any loss or damage (including,

without limitation, direct, indirect or consequential damages, or lost profits or production time) that results from the use

of unauthorized replacement parts or modification of the HYDRAULIC CONVERSION KIT. APS Resource’s sole ob-

ligation with regard to a HYDRAULIC CONVERSION KIT that proves to be defective in material or workmanship shall

be as set forth in its standard warranty above (i.e., APS Resource will, at its option, repair or replace the HYDRAULIC

CONVERSION KIT or portion thereof, without charge to the purchaser).

This limited warranty does not cover any failure caused by improper installation, abuse, negligence, or failure to prop-

erly maintain and adjust the HYDRAULIC CONVERSION KIT. This limited warranty will be void or of no effect if the

original purchaser does not notify APS Resource’s warranty department within ninety (90) days after the product defect

is discovered. Parts requiring replacement due to damage resulting from vehicle impact, abuse, or improper operation

are not covered by this warranty. APS Resource disclaims any responsibility or liability for any loss or damage that

results from the use of unauthorized replacement parts or modification of the HYDRAULIC CONVERSION KIT.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION ON THE

FACE HEREOF, AND THERE IS NO WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR

PURPOSE.

APS Resource warranties extend only to the HYDRAULIC CONVERSION KIT itself, and not to the dock leveler to

which it is installed.

APS Resource DISCLAIMS all warranties, express or implied, responsibility or liability for loss or damage of any kind

associated with the installation or maintenance of the HYDRAULIC CONVERSION KIT, including any liability for premature

product wear, product failure, property damage or bodily injury arising from improper installation or maintenance of the

HYDRAULIC CONVERSION KIT.

Summary of Contents for HTC Kit





























Search results

Summary of Contents for HTC Kit

Reviews:

Related manuals for HTC Kit

Brands by name

Popular brands

APS Resource HTC Kit, Installation And Owner'S Manual

Search results

Summary of Contents for HTC Kit

Reviews:

Related manuals for HTC Kit

Brands by name

Popular brands