manualshive.com logo in svg

APS Resource HTC Kit, Installation And Owner'S Manual

Share
Download
APS Resource HTC Kit Installation And Owner'S Manual Download Page 13

PAGE 12

©2010 4Front Engineered Solutions, Inc. - APS Resource 

    

             

AP4047 RA 11/10

            

INsTALLATION

POWER sYsTEM INsTALLATION

 1.  Find an open area near the rear of the subframe 

that will allow for easy access to service and 

maintain the motor/pump assembly.  

 

 

 

 2.  Weld the motor support bracket to the subframe in 

the above mentioned position.

 3.  Attach the motor to the motor support bracket.
 4.  Install all of the elbows onto the pump and 

cylinders. See Figure 17 and Parts List.

 5.  Install the velocity fuse and adapter to the main 

lifting cylinder.

 6.  Install the smaller hose from the lip cylinder to the 

pump.  

 7.  Install the larger hose from the pump to the velocity 

fuse on the main lifting cylinder.

 8.  Install the breather to the cylinder.
 9.  With the ramp resting on the maintenance strut, and 

the lip pendant, fill the oil reservoir near the top with 

MIL 5606 oil.

 

 

This location must be in an area large enough to 

prevent impact to the motor/pump unit when the 

deck is in fully below dock position.

The fittings should be positioned so as to connect 

the pump to the cylinders without bending or 

pinching the hoses.

Figure 17

Summary of Contents for HTC Kit





























Reviews:

No comments

Brands by name

Popular brands

Load more brands