manualshive.com logo in svg

APS Resource HTC Kit, Installation And Owner'S Manual

Share
Download
APS Resource HTC Kit Installation And Owner'S Manual Download Page 11

PAGE 10

©2010 4Front Engineered Solutions, Inc. - APS Resource 

    

             

AP4047 RA 11/10

            

INsTALLATION

Be certain that the lip hinges are clean and free 

of debris.

The cylinder will be mounted with the rod end 

connecting to the lip lug.

LIP CYLINDER INsTALLATION

 1.  Extend the lip to its maximum position.  

 

 

 2.  Secure the lip in the completely extended 

position.  

 3.  Find an area at the front of the leveler to install 

the lip cylinder without interfering with the 

operation of the leveler.  If not already there, cut 

an opening of 4½" wide by 5" tall into the front 

header to make room for the lip cylinder.  See 

Figure 14.

 

4.   Weld the lip cylinder lip lug (front cylinder lug) on 

the underside of the lip, against the front of the lip 

spool, or close to the lip rod.  See Figures 10 and 

14.

(IF APPLICABLE)

 5.  Position the lip cylinder ramp lug (rear cylinder 

lug) beneath the deck plate so that it is in line with 

the front cylinder lug.  The distance between the 

mounting holes from the front cylinder lug to the 

rear cylinder lug should be approx. 17".  See Figure 

10.

 6.  Tack weld the rear cylinder lug in position and 

attach the lip cylinder at both ends.  See Parts List 

for clevis pin information.

 7.  Weld on bridge bar clevis below the opening cut 

in the header, allowing enough room for the front 

cylinder lug movement (approximately 5” below 

hinge).  See Figure 14.

 8.  Carefully lower the lip to the pendant position.  

The lip cylinder must not stroke out when the lip is 

extended or bottom out when the lip is closed.

 9.  After making sure that the lip cylinder has 

the proper range, weld the rear cylinder lug 

permanently in position.

Figure 14

Summary of Contents for HTC Kit





























Reviews:

No comments

Brands by name

Popular brands

Load more brands