manualshive.com logo in svg

APS Resource HTC Kit, Installation And Owner'S Manual

Share
Download
APS Resource HTC Kit Installation And Owner'S Manual Download Page 10

PAGE 9

©2010 4Front Engineered Solutions, Inc. - APS Resource 

    

             

AP4047 RA 11/10

               

INsTALLATION

 8.  Bolt the clevis bracket (with the two bolts provided) 

to the flat base plate using the third and fifth 

threaded holes. The holes referred to are counted 

from the rear of the leveler.

9.   If the gap between the side of the clevis bracket and 

the side of the deck support channel is less than 

6¼", you will not have enough clearance for the 

cylinder pin.  It will be necessary to install the ramp 

cylinder into the clevis bracket before the clevis 

bracket is bolted to the base plate.

10.  Once bolted in place, weld the clevis bracket to 

the base plate.  The weld must be continuous and 

surround the entire perimeter of the clevis bracket.  

See Figure 11.

PIT FLOOR BRACKET INsTALLATION

 

 
 

 1.  Attach main lifting cylinder to the ramp bracket with 

the hose port upward towards the ramp.

 2.  Attach the clevis pit floor bracket assembly to the 

cylinder rod with the hardware provided.

 3.  Full extend the cylinder rod and allow the clevis pit 

floor bracket to lie flat on the pit floor.  Mark the 

location where the bracket makes contact with the 

pit floor is the pit floor bracket mounting location.  

 4.  Temporarily secure the pit floor bracket in place.
 5.  With a hoist, lower the ramp slowly to make sure the 

cylinder will not bottom out at the full below dock 

position.  Adjust the pit floor bracket if needed.

6.  Disassemble the pit floor clevis from the baseplate 

by unscrewing the (2) bolts.

7.  Place the baseplate in the marked off area.  

Securely fasten the baseplate to the pit floor using 

the (6) ¾" x 6" concrete anchors provided.  

8.   Reassemble the pit floor clevis to the baseplate, 

using the (2) bolts from Step 6.

9.   Weld the clevis to the baseplate.  The weld must be 

continuous and surround the entire perimeter of the 

clevis bracket.  See Figure 13. 

 

Always disconnect main power before doing any 

welding.  Always attach ground lug to the part 

being welded.

Main lifting cylinder will be installed with the rod 

end down.

20

Figure 12

Figure 11

Figure 13

ANCHOR HOLES

FOR 3/4" X 6" ANCHORS

BOLTS TO ASSEMBLE

PIT CLEVIS TO PIT

FLOOR PLATE BASE

1/4

Summary of Contents for HTC Kit





























Reviews:

No comments

Brands by name

Popular brands

Load more brands