APRILIA DORSODURO 2007 Service Station Manual Download

Page: 99 / 302

the vehicle ground connection: if it is correct, it means that the error cause is that the cable

is short circuit to positive and it is necessary to restore the cable harness between the EN-

GINE PIN 45 and the sensor PIN 1; if there is no continuity with the ground connection,

check the sensor connector and the Marelli control unit connector. If not OK, restore the

cable harness. If OK, check continuity between the ENGINE connector PIN 35 and the sen-

sor connector PIN 2: restore the cable harness if there is no continuity. If there is, it means

that the control unit does not supply the ground connection and therefore should be replaced.

Troubleshooting

•

If shorted to negative, check sensor correct resistance: if resistance is null, replace the sen-

sor; if resistance is correct, it means that the cable has ground connection: restore the cable

harness.

AXONE: LOGIC ERRORS

engine temperature sensor P0116

- signal not valid.

Error cause

•

An excessive temperature variation has been detected: for example, the cause may be a

contact resistance between the terminals.

Troubleshooting

•

Check the sensor connector and the ENGINE connector of the Marelli control unit.

NOTES

No error is detected if the sensor does not work correctly or the control unit connector

or sensor terminals are rusty: then check through Axone if the temperature indicated is plausible

in relation to the engine temperature. Check also that the sensor electrical characteristics are

observed: replace the sensor if not OK; if it is OK, check the sensor connector and the Marelli

control unit connector

Air temperature sensor

INTAKE AIR TEMPERATURE SENSOR

Function

It tells the control unit the intake air temperature in

order to calculate oxygen presence so as to opti-

mise the petrol quantity necessary for correct com-

bustion.

Operation / Operating principle

NTC type sensor (resistance sensor, inversely

variable with temperature).

Level in wiring diagram:

Temperature sensors

Location:

DORSODURO

Electrical system

ELE SYS - 99

Summary of Contents for DORSODURO 2007















































































































































































































































































































Search results

Summary of Contents for DORSODURO 2007

Reviews:

Related manuals for DORSODURO 2007

Brands by name

Popular brands

APRILIA DORSODURO 2007, Service Station Manual

Search results

Summary of Contents for DORSODURO 2007

Reviews:

Related manuals for DORSODURO 2007

Brands by name

Popular brands