APRILIA DORSODURO 2007 Service Station Manual Download

Page: 140 / 302

•

Working on the left side, unscrew and

remove the lower bolt.

•

Working on the right side, slightly slide

off the lower bolt.

•

Collect the spacer on the opposite

side.

•

Remove the lower pin and collect the

washer.

•

Lower the engine.

See also

Vehicle preparation

Installing the engine to the vehicle

•

Place the engine on a suitable lower stand.

•

Lift the engine.

•

Place the engine so that the rear attachments on the chassis are aligned.

Engine from vehicle

DORSODURO

ENG VE - 140

Summary of Contents for DORSODURO 2007















































































































































































































































































































Search results

Summary of Contents for DORSODURO 2007

Reviews:

Related manuals for DORSODURO 2007

Brands by name

Popular brands

APRILIA DORSODURO 2007, Service Station Manual

Search results

Summary of Contents for DORSODURO 2007

Reviews:

Related manuals for DORSODURO 2007

Brands by name

Popular brands