APRILIA DORSODURO 2007 Service Station Manual Download

Page: 95 / 302

•

If the circuit is open, short circuit to negative, check the filter casing large connector, the

Marelli control unit connector and the sensor connector; If not OK, restore. If everything is

OK, and with key set to OFF, check if there is continuity between the VEHICLE PIN 5 of the

Marelli control unit and the sensor connector PIN 3: if there is no continuity, restore the cable

harness. If there is continuity, check the cable earth insulation: if there is continuity to ground,

restore the cable harness; if not, with key set to ON check that the voltage on sensor con-

nector PIN 1 is approx. 5 V: if this is not correct, set the key to OFF and check continuity

between the ENGINE connector PIN 15 and the sensor connector PIN 1: If not OK, restore

the cable harness; if it is OK, replace the control unit. if there is 5V voltage at PIN 1, and

with key set to ON, check the continuity to ground of the sensor connector PIN 3: If not OK,

restore cable harness; if it is OK, replace the sensor.

AXONE: LOGIC ERRORS

front cylinder air pressure sensor P0107

- signal not valid.

Error cause

•

According to the engine operation data (rpm, throttle, etc.) an average value for the intake

pressure is estimated: if the value read deviates by a given percentage, this error is activa-

ted. The most frequent causes can be: abnormal resistance in the sensor circuit (for

example, rusted terminals) or sensor with poor performance.

Troubleshooting

•

Check the filter casing large connector, the Marelli control unit connector and the sensor

connector; if not OK, restore. If everything is OK, check that cable resistance between VE-

HICLE connector PIN 34 and sensor connector PIN 3 is a few tenths of an Ohm. If it is above

that value, restore cable harness. Replace the sensor if it is correct.

rear cylinder air pressure sensor P0108

- signal not valid.

Error cause

•

According to the engine operation data (rpm, throttle, etc.) an average value for the intake

pressure is estimated: if the value read deviates by a given percentage, this error is activa-

ted. The most frequent causes can be: abnormal resistance in the sensor circuit (for

example, rusted terminals) or sensor with poor performance.

Troubleshooting

•

Check the filter casing large connector, the Marelli control unit connector and the sensor

connector; if not OK, restore. If everything is OK, check that resistance between VEHICLE

connector PIN 5 and sensor connector PIN 3 is a few tenths of an Ohm. If it is above that

value, restore cable harness. Replace the sensor if it is correct.

Error for unexpected intake air in the front cylinder manifold P0210

- signal not valid.

Error cause

DORSODURO

Electrical system

ELE SYS - 95

Summary of Contents for DORSODURO 2007















































































































































































































































































































Search results

Summary of Contents for DORSODURO 2007

Reviews:

Related manuals for DORSODURO 2007

Brands by name

Popular brands

APRILIA DORSODURO 2007, Service Station Manual

Search results

Summary of Contents for DORSODURO 2007

Reviews:

Related manuals for DORSODURO 2007

Brands by name

Popular brands