manualshive.com logo in svg

APRILIA DORSODURO 2007, Service Station Manual

Share
Download
APRILIA DORSODURO 2007 Service Station Manual Download Page 86

Engine rpm sensor

ENGINE REVOLUTION SENSOR

Function

It informs crankshaft position and speed to the

Marelli control unit.

Operation / Operating principle

Inductive sensor: sinusoidal-type generated volt-

age; two teeth are missing on the flywheel for the

reference position.

Level in wiring diagram: r

evolution sensor

Location:

•

on the vehicle: inside the flywheel cov-

er

•

connector (if available): near the Mar-

elli control unit

Electrical characteristics:

•

Resistance at ambient temperature:

130 +/- 20 Ohm

Pin-out:

1. Negative signal

2. Positive signal

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL CON-
CEPTS OF ELECTRICAL TROUBLESHOOTING FOUND AT THE BEGINNING OF THE CHECKS
AND CONTROLS SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

AXONE: PARAMETERS

Engine rpm

AXONE: STATUSES

Synchronised panel

Example value:

Start-up_Lean_Rich_Fault due to rich value_Fault due to lean value

If the probe connector is removed (voltage almost equal to zero), the status is Fault due to lean value

Example value:

No_under analysis_standby_Yes

The parameter refers to the engine revs signal: in case the signal has not been correctly identified yet,

the under analysis or standby statuses may be displayed.

AXONE: ACTIVATIONS

-

AXONE: ELECTRICAL ERRORS

-

Electrical system

DORSODURO

ELE SYS - 86

Summary of Contents for DORSODURO 2007















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands