APRILIA DORSODURO 2007 Service Station Manual Download

Page: 116 / 302

•

Signal not within the expected value drawn according to the values of the intake pressure.

Troubleshooting

•

Check the parameter of the Potentiometer 2 Rear throttle (voltage) to get which signal the

control unit receives and to compare it to the Potentiometer 2 Front throttle (voltage). Check

the throttle body connector as well as the throttle control unit connector. Check that cable

resistance between the throttle body connector (PIN 4) and the throttle control unit (PIN 5B)

is a few tenths of an Ohm. If this is not the case, restore the cable harness. If the value is

correct, replace the complete throttle body.

Rear throttle position sensors P0129

- illogical signal.

Error cause

•

Potentiometer 1 and potentiometer 2 do not show a logical value: the sum of the two voltages

should be constant. The cause may be a malfunction in one of the two sensors or an ab-

normal resistance in one of the two circuits.

Troubleshooting

•

Check the throttle body connector as well as the throttle control unit connector. Check that

cable resistance between the throttle body connector (PIN 1) and the throttle control unit

(PIN 6B) is a few tenths of an Ohm. Check that cable resistance between the throttle body

connector (PIN 4) and the throttle control unit (PIN 5B) is a few tenths of an Ohm. If one of

the two is different, restore the cable harness. If correct, replace the complete throttle body.

Front throttle Limp Home autodetection P0160

- test failed.

Error cause

•

Throttle position, kept by the springs, not within the expected range (at each key ON). The

instrument panel does not indicate the presence of this error even in the ATT status.

Troubleshooting

•

Check if the throttle body and the intake duct are clean. If they are, replace the throttle body.

Front throttle mechanical springs autodetection P0161

- test failed.

Error cause

•

Return time of the throttle, kept in position by the springs, not within the expected limits: the

causes can be a deterioration of the performance of the springs or excessive throttle friction

(at each key ON).

Troubleshooting.

•

Check if the throttle body and the intake duct are clean. If they are, replace the throttle body.

Front throttle minimum mechanical position autodetection P0162

- test failed.

Error cause

•

Position of the throttle stop not within the expected range (at each key ON).

Troubleshooting.

Electrical system

DORSODURO

ELE SYS - 116

Summary of Contents for DORSODURO 2007















































































































































































































































































































Search results

Summary of Contents for DORSODURO 2007

Reviews:

Related manuals for DORSODURO 2007

Brands by name

Popular brands

APRILIA DORSODURO 2007, Service Station Manual

Search results

Summary of Contents for DORSODURO 2007

Reviews:

Related manuals for DORSODURO 2007

Brands by name

Popular brands