APRILIA DORSODURO 2007 Service Station Manual Download

Page: 249 / 302

REAR WHEEL RIM

•

Using a dial gauge, check that the ra-

dial (A) and the axial eccentricity (B) of

the rim (2) do not exceed the limit val-

ue.

An excessive eccentricity is usually caused by

worn or damaged bearings. Replace the rim (2) if

after replacing the bearings, the value is not within

the specified limit.

Characteristic

Maximum radial and axial eccentricity:

2 mm (0.0079 in)

Shock absorbers

Removing

•

Place the optional under-sump and rear wheel service stands.

•

Unscrew and remove the upper screw and collect the washer.

•

Loosen the under-sump optional serv-

ice stand to lower the engine.

•

Undo and remove the lower screw and

collect the nut.

•

Remove the shock absorber.

DORSODURO

Suspensions

SUSP - 249

Summary of Contents for DORSODURO 2007















































































































































































































































































































Search results

Summary of Contents for DORSODURO 2007

Reviews:

Related manuals for DORSODURO 2007

Brands by name

Popular brands

APRILIA DORSODURO 2007, Service Station Manual

Search results

Summary of Contents for DORSODURO 2007

Reviews:

Related manuals for DORSODURO 2007

Brands by name

Popular brands