manualshive.com logo in svg

APRILIA DORSODURO 2007, Service Station Manual

Share
Download
APRILIA DORSODURO 2007 Service Station Manual Download Page 98

•

Resistance at 25°: 2.05 kOhm +/- 100

Ohm

•

Resistance at 60°: 575 Ohm +/- 15

Ohm

•

Resistance at 90°: 230 Ohm +/- 5 Ohm

Pin-out:

1. Yellow brown: 0-5 V signal: PIN B1

2. Brown: PIN B2 ground connection

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL CON-
CEPTS OF ELECTRICAL TROUBLESHOOTING FOUND AT THE BEGINNING OF THE CHECKS
AND CONTROLS SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

AXONE: PARAMETERS

Engine temperature

Example value: 75° C

In case of recovery, this value is set by the control unit.

Engine Temp. before Recovery

Example value: -40° C

Value drawn from the signal read without taking into account any recovery: the value in the example

refers to an open circuit.

AXONE: ELECTRICAL ERRORS

engine temperature sensor P0115

 - open circuit, shorted to positive / shorted to negative.

Error cause

•

If the circuit is open, shorted to positive: excessive voltage has been detected at PIN 45 of

the ENGINE connector. If shorted to negative: voltage equal to zero has been detected at

PIN 45 of the ENGINE connector.

•

If the circuit is open, shorted to positive: check the sensor connector and the Marelli control

unit connector. If they are OK, check sensor continuity: replace the sensor if not OK; if it is

OK, check the continuity between the ENGINE connector PIN 45 and the sensor PIN 1:

restore cable harness if there is not continuity; if it is OK, reconnect the control unit connector

and, with key set to key ON, check the continuity between the sensor connector PIN 2 and

Electrical system

DORSODURO

ELE SYS - 98

Summary of Contents for DORSODURO 2007















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands