APRILIA DORSODURO 2007 Service Station Manual Download

Page: 56 / 302

4. Instrument panel

5. Engine control unit

6. Front headlamp

7. Start-up relay

8. Coils

9. Spark plugs

10.Starter motor

11.Rear light

12.Auxiliary fuses

13.Main fuses

14.Throttle grip position sensor

15.Gear in neutral sensor

16.Revolution sensor - pick up

17.Engine temperature sensor

18.Throttle control unit

19.Lambda Probe

20.Fall sensor

21.Main injection relay

CAUTION

A RELAY CANNOT BE IDENTIFIED BASED ONLY ON THE FOLLOWING INDICATIONS: THIS
SHOULD BE DONE ALSO IDENTIFYING THE COLOUR OF THE RELAY CABLES.

RELAY LAYOUT ON THE WIRING DIAGRAM AND ON THE VEHICLE

LIGHT LOGIC RELAY

•

Location on the wiring diagram: 7

•

Location on the vehicle: under the fuel tank, left side, second relay starting from the front.

START-UP RELAY

•

Location on the wiring diagram: 34

•

Location on the vehicle: under the fuel tank, right side, fifth relay starting from the front, below

in relation to the line of the other relays.

RETENTION RELAY

•

Location on the wiring diagram: 37

•

Location on the vehicle: under the fuel tank, right side, second relay starting from the front.

CONTROL RELAY

•

Location on the wiring diagram: 38

•

Location on the vehicle: under the fuel tank, right side, first relay starting from the front.

MAIN INJECTION RELAY

•

Location on the wiring diagram: 39

Electrical system

DORSODURO

ELE SYS - 56

Summary of Contents for DORSODURO 2007















































































































































































































































































































Search results

Summary of Contents for DORSODURO 2007

Reviews:

Related manuals for DORSODURO 2007

Brands by name

Popular brands

APRILIA DORSODURO 2007, Service Station Manual

Search results

Summary of Contents for DORSODURO 2007

Reviews:

Related manuals for DORSODURO 2007

Brands by name

Popular brands