API Legacy AXS Operator'S Manual Download Page 17

Page: 17 / 103

L e g a c y A X S

A P I

Channel Input

The channel has three audio input sources:

•

Preamp Output: The output of the preamp in the upper 200 slot (typically 212 Mic Preamp)

•

Line Input: Balanced line input, normalled to multitrack (DAW) returns

•

Alternate Line Input (ALT): Alternate balanced line input

The Large and Small Fader paths can accept only one audio source at a time.

The output upper 200 slot Preamp is the default source the Small Fader path. The Line Input is the

default source for the Large Fader. The inputs to the paths can be swapped on individual channels by

engaging the

FLIP

button on the 968 Input Module. This will route the Preamp output to the Large

Fader and the Line Input to the Small Fader. Engaging the FLIP button in the Master Section will swap

fader path inputs on a global basis.

The Alternate Line Input can replace the Preamp output as the source for the Small Fader path. This

provides additional balanced line-level inputs for recording and mixing. Engaging the

ALT

button on

the 968 Input Module will route the Alternate Line Input to the Small Fader path on individual channels.

Engaging the SM ALT LINE button in the Master Section will route the Alternate Line Inputs to the

Small Fader paths on a global basis.

The Alternate Line Input can be routed to the Large Fader by engaging the

ALT

and

FLIP

buttons on

individual channels or console-wide by the SM ALT LINE and FLIP buttons in the Master Section.

Upper 200 Slot

The upper 200 slot is designed to house the channel preamp. Two API 200 Series preamplifier modules

are available for installation. Only the upper 200 slot is wired to accept a preamp, so only one preamp

can be installed in each channel strip:

212 Microphone Preamplifier (standard configuration)

205 Direct Input

212 Mic Preamp

Features

•

Wide range GAIN control

•

-20dB Pad

•

48V phantom power switch

•

Mic input transformer

•

LED output Meter

•

Uses API 2520 Op-Amp

•

All discrete circuit

•

Transformer coupled inputs & outputs to +28dBu

The tone of the 212 Mic Preamp finds its roots in the classic API 2488 series all

discrete recording consoles, best known for the famed "LA" sound. This same mic

preamp design is packaged into a compact module with features like a continuously

adjustable Gain control and a 5-segment LED meter.

An audio chain is only as strong as its weakest link. Often, emphasis is placed on obtaining the highest

quality microphones, while neglecting the integrity of the mic preamp. The API 212 incorporates the

same circuit as the legendary API console input modules, dating from the 1970's up to and including

the Model 1608, thus preserving its sonic qualities. This mic-pre articulates high frequencies with great

detail, while delivering the big sounding, warm bottom end that API is famous for. Whether it's a live

performance or the private setting of a studio session, the 212 will capture every nuance of the

moment.

The 212 Mic Preamp’s all discrete circuitry features the API 2520 op-amp and input and output

transformers. A -20dB pad is provided, allowing the level feeding the mic transformer to be reduced

by 20dB, while keeping the proper load on both the mic and transformer. 48V Phantom power can be

Summary of Contents for Legacy AXS








































































































Search results

Summary of Contents for Legacy AXS

Reviews:

Brands by name

Popular brands

API Legacy AXS, Operator'S Manual

Search results

Summary of Contents for Legacy AXS

Reviews:

Brands by name

Popular brands