manualshive.com logo in svg

ANK L5, Construction Manual

The ANK L5 Construction Manual is your go-to resource for all your construction needs. With this comprehensive manual, you can easily find step-by-step instructions, diagrams, and helpful tips to successfully complete any construction project. Download for free at manualshive.com and effortlessly access this invaluable manual anytime, anywhere.

Share
Download
background image

Copyright © 2019 AudioNote Kits 
www.AudioNoteKits.com 
[email protected]

  

 

 

 

 

 

 

 

 

Page 69

 

 

Section 11 

 

Final Thoughts 

 

11.1  Congratulations 

 

If you've made it to this point then CONGRATULATIONS! — you are ready to insert your L5 Signature 
Phono Stage into your system and enjoy it. 
 

 

 
11.2  Cables 

 

In  our  experience,  a  high  quality  power  cable  and  good  interconnects  should  make  a  noticeable 
improvement to the sound. 

 

11.3  Tube Rolling 

 

We feel that the sound of the ANK Audio Kits L5 Signature Phono Stage is truly sublime.  It provides a 
highly  detailed  and  transparent  presentation  with  gorgeous  sonics.    Rolling  some  quality  new 
production tubes and/or some nice NOS tubes in the 12AX7, 6922, and 5U4G positions will allow you to 
tailor the sound to your particular preferences. 
 

 

 

Summary of Contents for L5













































































Reviews:

No comments

Related manuals for L5

Brands by name

Popular brands

Load more brands