manualshive.com logo in svg

ANK L5, Construction Manual

The ANK L5 Construction Manual is your go-to resource for all your construction needs. With this comprehensive manual, you can easily find step-by-step instructions, diagrams, and helpful tips to successfully complete any construction project. Download for free at manualshive.com and effortlessly access this invaluable manual anytime, anywhere.

Share
Download
background image

Copyright © 2019 AudioNote Kits 
www.AudioNoteKits.com 
[email protected]

  

 

 

 

 

 

 

 

 

Page 34

 

 

4.2  Installing the Valve Base 

 

We'll begin by installing the 8-pin valve base for the 5U4G rectifier. 
 

 

 

Use masking tape to secure the valve base to the board prior to soldering.  

The key is to make sure the 

valve base is level

:  if you have a base that is soldered in on an angle then your tube will lean over!  

Solder from the underside of the board.  Use just a little solder to secure each pin to the board and 
start with two pins which are opposite to each other to make sure the base stays level — then you 
can add more solder.  In the end you can fill up the entire valve base hole.  

Be very careful not to let 

any solder bridge to the next pin as this will cause a short!  

If you wish to — or think you need to, you 

can 'touch them up' from the top, then back once again to the bottom, and all should be well.  When 
you do the touch ups just give them a very short bit of heat and a tiny bit of additional solder. 
 

   Install the 8-pin valve base.  

Be very careful to align the tab 'cut-out' on the top of the valve base 

with the tab stencil on the board.  

Take your time soldering on the underside of the board as it 

requires a fair bit of heat and solder to adhere the pins to the board.  No rushing! 

 

4.3  Installing the Capacitors 

 

   Install the Mundorf MCap at EC1.

 

   Install the 2 4-pole MLytic Power Supply capacitors at EC2 and EC3.  These can only go in one 

direction.

 

   Install the 5 standoffs.

 

 

 

Summary of Contents for L5













































































Reviews:

No comments

Related manuals for L5

Brands by name

Popular brands

Load more brands