manualshive.com logo in svg

ANK L5, Construction Manual

The ANK L5 Construction Manual is your go-to resource for all your construction needs. With this comprehensive manual, you can easily find step-by-step instructions, diagrams, and helpful tips to successfully complete any construction project. Download for free at manualshive.com and effortlessly access this invaluable manual anytime, anywhere.

Share
Download
background image

Copyright © 2019 AudioNote Kits 
www.AudioNoteKits.com 
[email protected]

  

 

 

 

 

 

 

 

 

Page 40

 

 

5.5  Installing the Bridge Rectifiers 
 

Quantity 

Designation 

Description 

Part Number 

2 

B1, B3 

Bridge Rectifier  GBU4M-BPMS-MD 

 

A Bridge Rectifier accepts an AC voltage and generates a DC voltage which, in the Phono Stage, is 
used as the filament voltage.  You'll see a notch on the Bridge Rectifiers (part number: GBU4M): match 
the notch with the '+' (POSITIVE) stencil on the board. 

 

 

 

The Bridge rectifier has an edge notched on it that lines up with the board. 
 

  Install the 2 GBU4M

8

 Bridge Rectifiers at B1 and B2. 

 
 

 

                                                           

8

 The picture actually shows a slightly different part number; you can just ignore it. 

Summary of Contents for L5













































































Reviews:

No comments

Related manuals for L5

Brands by name

Popular brands

Load more brands