ANK L5 Construction Manual Download Page 62 | Manualshive

Page: 62 / 76

background image

Copyright © 2019 AudioNote Kits
www.AudioNoteKits.com
[email protected]

Page 62

8.4 Connecting the Shielded Audio Note (UK) AN-A Input and Output Cables

The  AN-A  cable  is  basically  a  shielded  cable  with  a  Ground  sheaf  around  it  and  two  Signal
conductors, Red and White.  We've prepared the cable: the Red lead is the Signal and the White lead is
tied to the Ground sheaf.  This AN-A will need “tinning” as there is a coating on the stranded wire.

When working with the RCA jacks we use the following procedure:



Tin the RCA Red (signal) and Black (ground) leads



Put a puddle of solder in the center of the RCA jack



Tin the ground tab on the RCA jack



Heat the solder puddle and slide the Red tinned lead into the center of it; it should adhere
immediately



Heat the tinned Black lead as it makes contact with the ground tab on the RCA; similarly, it
should adhere immediately

  Connect the Red wire to one of the input RCAs and the White wire to its Ground post.
  Do the same for the other channel.
  On the Phono board side the White/Ground sheaf are connected to the Ground input and the Red

to the Signal.

«
...
60
61
62
63
64
...
»

Summary of Contents for L5













































































Reviews:

No comments

Related manuals for L5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands