manualshive.com logo in svg

ANK L5, Construction Manual

The ANK L5 Construction Manual is your go-to resource for all your construction needs. With this comprehensive manual, you can easily find step-by-step instructions, diagrams, and helpful tips to successfully complete any construction project. Download for free at manualshive.com and effortlessly access this invaluable manual anytime, anywhere.

Share
Download
background image

Copyright © 2019 AudioNote Kits 
www.AudioNoteKits.com 
[email protected]

  

 

 

 

 

 

 

 

 

Page 35

 

 

4.4  Shield Installation 

 

 

On the underneath of the shield, locate the hole that has no paint on it — this will match up with 
a  hole  on the  chassis  that  is  also  unpainted in  order to ensure  a  good grounding of  the  shield 
when installed in the chassis. 

 

     

 

 
Here you can see the correct positioning of the shield: 

 

 

You'll also see several holes in the shield panel: these will be used in the interwiring to route wires 
from one side of the Phono Stage to the other. 
 

  Install the supplied grommets in the shield and secure it in place using 3 M4 10mm screws and 

nuts place; insert the screws from underneath the chassis. 

Summary of Contents for L5













































































Reviews:

No comments

Related manuals for L5

Brands by name

Popular brands

Load more brands