ANK L5 Construction Manual Download Page 5 | Manualshive

Page: 5 / 76

background image

Copyright © 2019 AudioNote Kits
www.AudioNoteKits.com
[email protected]

Page 5

Section 1

Introduction

Thanks for purchasing the ANK Audio Kits L5 Signature Phono Stage. This Phono Stage represents a
stunning addition to our L5 product line and we believe it is truly one of the finest phono stages on
the planet! And our goal is to provide you with the highest quality kit that you will build from
scratch with these instructions.

This is very high end and sophisticated piece of audio equipment that will surely become a showpiece
of  your  sound  system.    We're  excited  that  you've  chosen  to  join  us  in  enjoying  and  appreciating
superb audio and we've created this manual to help guide you through each step of the assembly
process with as much detail and clarity as possible.  To facilitate the build process, the manual has
been divided into a number of sections, each focusing on a separate aspect of the system:  follow the
sections  in  order  and  we  guarantee  you  not  only  a  problem-free  experience,  but  a  pleasant  time
doing so.  If you are new to building kits, or if at any time you feel as though you need help or advice,
feel free to contact us and we will do whatever it takes to get you on the right track.

«
...
3
4
5
6
7
...
»

Summary of Contents for L5













































































Reviews:

No comments

Related manuals for L5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands