ANK L5 Construction Manual Download Page 68 | Manualshive

Page: 68 / 76

background image

Copyright © 2019 AudioNote Kits
www.AudioNoteKits.com
[email protected]

Page 68

Section 10

Finishing Touches

10.1 Installing the Front Faceplate

Remove the protective films from the front and back of the front faceplate.
Install the front faceplate using four Black M4 CSK flat head screws.

10.2 Installing the LED

Carefully trim the LED leads so that they are not exposed.
Glue or attach (with some Blu Tack) the LED holder to the front panel so that the LED protrudes

through the designated hole, as shown below:

10.3 Last Looks Inside

Before you close things up, it's not a bad idea to do a final visual inspection, particularly to assure
yourself that none of the interwiring is too close to things that get hot — like the tubes and the 10W
resistors on the tag strips.

10.4 Installing the Chassis Top

Install the chassis top using the provided hardware.

«
...
66
67
68
69
70
...
»

Summary of Contents for L5













































































Reviews:

No comments

Related manuals for L5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands