manualshive.com logo in svg

ANK L5, Construction Manual

The ANK L5 Construction Manual is your go-to resource for all your construction needs. With this comprehensive manual, you can easily find step-by-step instructions, diagrams, and helpful tips to successfully complete any construction project. Download for free at manualshive.com and effortlessly access this invaluable manual anytime, anywhere.

Share
Download
background image

Copyright © 2019 AudioNote Kits 
www.AudioNoteKits.com 
[email protected]

  

 

 

 

 

 

 

 

 

Page 66

 

 

9.3  Initial Tests 

 

Let's begin by doing some basic tests, with the Phono Stage off. 
 
A good place to start is to measure resistance.  Let's have a look at the Chassis Ground, an important 
(almost) universal ground point in the Phono Stage. 
 
Try this: 
 

 

Place your multimeter in Connectivity mode 

 

Put one probe on the Chassis Ground 

 

Check the following points to verify that there is zero ohms or close (a couple of ohms is OK) 
between these ground points: 

 

IEC Socket Ground 

 

GND on the Phono board 

 
Let’s move on to our first real power-up. 

 

9.4  First Power-Up 

 

IMPORTANT NOTE 

 
Follow the turn-on procedure carefully.  DO NOT AT ANY TIME ONLY INSTALL THE 5U4G RECTIFIER 
TUBE WITHOUT ANY OTHER TUBES INSTALLED.  The reason for this is that the rectifier is counting on 
having a specific load to drive.  If the  rectifier is used without other tubes installed then the unit will 
'see' significantly higher DC voltages, which can overextend the Power Supply capacitors.  You could 
possibly  start  hearing  cracking  noises  and  then  who  knows  what,  as  they  are  beyond  their 
maximum voltage ratings. 

 
 

 

 

PLEASE BE AWARE OF PROPER ELECTRICAL SAFETY. 

 

There are sufficient voltages in this kit to give you a very nasty and harmful 

shock, so be careful when powering on, debugging, and probing around. 

 

If the initial resistance checks are OK then you can install the 12AX7 and 6922 tubes. 

 

 

 

Summary of Contents for L5













































































Reviews:

No comments

Related manuals for L5

Brands by name

Popular brands

Load more brands