![background image](http://html1.mh-extra.com/html/amx/nxa-wapzd1000/nxa-wapzd1000_operation-reference-manual_2937893051.webp)
Configure Tab
47
NXA-WAPZD1000 ZoneDirector Smart WLAN Controller
7.
If your APs are on different subnets from the device, click the check box next to DHCP Option 43 to
enable Layer 3 discovery of the NXA-WAPZD1000 by the APs.
8.
Click Apply.
Viewing DHCP Clients
To view a list of current DHCP clients, click the click here link at the end of the “To see all currently assigned
IPs by DHCP server...” sentence. A table appears and lists all current DHCP clients with their MAC addresses,
assigned IP addresses, and the remaining lease time.
Enabling an Additional Management Interface
The additional management interface is created for receiving or transmitting management traffic only. The
management IP address can be configured to allow an administrator to access the NXA-WAPZD1000
remotely from a different subnet from the AP network.
It can also be used for Smart Redundancy -- when redundant NXA-WAPZD1000s are deployed, you can
create a separate management interface to be shared by both devices. This shared management IP address is
enabled under the Device IP Settings section, and must be configured identically on both NXA-WAPZD1000s.
For more information on Smart Redundancy, please refer to the Enabling Smart Redundancy section on
page 17.
To enable an additional management interface:
1.
Go to Configure > System.
2.
In the Device IP Settings section, click the Click Here link next to the text “If ZoneDirector needs another
interface for management traffic...”
3.
Click the box next to Enable Management Interface, and enter the IP Address, Netmask and VLAN
information for the additional interface.
4.
Click Apply to save your settings.
5.
If the Management Interface is to be shared by two devices, repeat steps 1-5 for the other NXA-
WAPZD1000.
Checking the Current Log Settings
To review and customize the internal log settings:
1.
Go to Configure > System.
2.
Scroll down to Log Settings.
3.
Make your selections from these syslog server options:
Event Log Level: Select one of the three logging levels: “Show More,” “Warning and Critical
Events,” or “Critical Events Only.”
Remote Syslog: To enable syslog logging, select the “Enable reporting to remote syslog server at”
check box, and then type the IP address in the box provided.
4.
Click Apply to save your settings. The changes go into effect immediately.
If you typed an invalid value in any of the text boxes, an error message appears and
prompts you to let the NXA-WAPZD1000 automatically correct the value. Click
OK
to
change it to a correct value.
If a management interface is used for Web UI management, the actual IP address
must still be used when configuring the NXA-WAPZD1000 as a client for a backend
RADIUS server or in any SNMP systems. If two devices are deployed in a Smart
Redundancy configuration, both of the actual IP addresses must be used rather than
the management IP address.
Summary of Contents for NXA-WAPZD1000
