manualshive.com logo in svg

AMX AutoPatch CP-15, Instruction Manual, Page: 35 / 38

Share
Download
AMX AutoPatch CP-15 Instruction Manual Download Page 35

Installing a CP-15 Remote Control Panel

32

CP-15 Instruction Manual

5.

Insert the power plug from each of the AMX AutoPatch transformers into the power jack on each of 
the CP-15 remote panels.

6.

Place the panels in rack(s) or in other permanent installation locations.

7.

Plug the wall transformers into the power sources.

We recommend completing the installation by performing a test switch to make sure the system is 
working properly (see below).

Note:

 

If experiencing difficulties, insert a 120 ohm resistor in the outer contacts of the unused Comm 

Link on the last remote of a large daisy chain and tighten the screws. If problems persist, contact 
technical support (see page 34).

Completing the Installation

We recommend completing the installation by executing a test switch routing Input 1 to Output 2 on the 
level designated by the enclosure’s “Connector Guide.”

To execute a test switch:

1.

Press the Function Key. 
The Function menu appears.

2.

Press the Select Key to choose Change.

3.

Press Input Key 2.
Input Key 2 flashes indicating that it is ready to switch.

4.

Press Output Key 1.
Output Key 1 illuminates indicating that it is ready to accept the switch

5.

Press the Take Key.
Input 2 switches to Output 1, and the keys turn blue.

If the test switch does not execute correctly, check all system connections and retry the test switch before 
contacting technical support, (for contact information, see page 34).

Summary of Contents for AutoPatch CP-15







































Reviews:

No comments