background image

88D User Manual 

  4 

3.i

 

Surround Sound................................................................................37

 

How the Surround Sound system works ............................................................... 37

 

Surround Stem Selection and Routing.................................................................. 38

 

Surround Monitoring.............................................................................................. 39

 

Monitoring the Stems ............................................................................................ 39

 

Surround Monitoring Formats ............................................................................... 40

 

Mono ..................................................................................................................... 40

 

LCRS Pre and Post Decode Monitoring................................................................ 40

 

Surround Monitor Solo and Cut............................................................................. 41

 

3.j

 

Joysticks............................................................................................42

 

Joystick Automation .............................................................................................. 42

 

Monitor Facilities Rack .......................................................................................... 44

 

Audio Paths........................................................................................................... 44

 

Monitor Inputs ....................................................................................................... 44

 

External Inputs ...................................................................................................... 44

 

Routing and Mixing ............................................................................................... 44

 

LSRS Flip .............................................................................................................. 44

 

Level...................................................................................................................... 44

 

Speaker Calibration............................................................................................... 45

 

Return Talkback .................................................................................................... 45

 

4.

 

 Working With Signal Paths .................................................................47

 

Channels ............................................................................................................... 47

 

Tracks ................................................................................................................... 47

 

Main Outputs......................................................................................................... 48

 

Groups .................................................................................................................. 49

 

Auxiliaries.............................................................................................................. 49

 

Auxiliary Contributions .......................................................................................... 49

 

Cues...................................................................................................................... 50

 

Externals ............................................................................................................... 50

 

Films...................................................................................................................... 50

 

System Paths ........................................................................................................ 51

 

SEL ....................................................................................................................... 51

 

LISTEN.................................................................................................................. 52

 

TALKBACK ........................................................................................................... 52

 

FILM LISTENS ...................................................................................................... 52

 

5.

 

Routing ..................................................................................................53

 

I/O Routing ............................................................................................................ 53

 

Path Routing ......................................................................................................... 53

 

I/O Routing from the console surface.................................................................... 53

 

Route Stem ........................................................................................................... 54

 

Interrogating I/O Routing....................................................................................... 54

 

Path Routing with the Access Keys ...................................................................... 54

 

6.

 

Machine Control....................................................................................55

 

Standard Functions ............................................................................................... 55

 

Shuttle ................................................................................................................... 56

 

Jog ........................................................................................................................ 56

 

Locate ................................................................................................................... 57

 

Auto Locate ........................................................................................................... 57

 

Locate Labels........................................................................................................ 57

 

Cycle ..................................................................................................................... 58

 

Auto Cycle............................................................................................................. 58

 

Cycle Labels.......................................................................................................... 58

 

Pre Roll ................................................................................................................. 59

 

Post Roll................................................................................................................ 59

 

Summary of Contents for 88D






















































































Reviews: