manualshive.com logo in svg

AMI 227, Operation Manual, Page: 84 / 86

Share
Download
AMI 227 Operation Manual Download Page 84

 

 

MODEL 227 

OPERATION MANUAL

 

Doc # 740063 Rev E 

 

SECTION VIII - OPTIONS 

 

8.1 

M227/207-CW & M207-CW COOLING UNIT SPECIFICATIONS/INSTALLATION 

 

 

 4.  Installation 

 

 

 

3.  Before mounting the M277/207-CW or M207-CW on to the M-227  remove 

 

 

    the fill cap and add the water.  Replace the fill cap. Remove the pins 

 

 

  attached to each corner post (see figure 9).  Locate the CW Power Cord 

 

 

  exiting a hole in the top of the CW unit.  Pull enough of the cord out so it 

 

 

  dangles over the side of the unit.  

 

 

 

4.  Move the M-227 onto the CW unit and insert the corners onto the posts 

 

 

  of the CW Unit.  Locate the M-227 Coolant Unit Connector located on the 

 

 

  panel on the AC Input side of the M-227. Insert the CW cable connector 

 

           into the M-227 connector.   Secure the CW unit with the pins that were 

 

 

  removed (figure 9). 

 

 

 

5.  Install the adapter cable coolant hoses per section III.  Re-connect the M-227 

 

 

     power cable. 

 

 

5.  Operation   

 

 

 

1.  When all connections have been made per Section III and a coolant flow  

 

 

  path is created, turn the M-227 ON and set the CW ON/OFF 

 

 

  switch to ON.  The pump should start circulating coolant. 

 

WARNING 

 

 

  DO NOT OPERATE the water cooling unit WITHOUT coolant in the tank 

 

 

  OR WITHOUT a water flow path (water OUT to IN through a weld head). 

 

 

 

2.  Both CW units contain a flow sensor. If the Set Up Screen Coolant Fault 

 

 

  Mode is ON the M-227 will look to see if the Cooling Unit is connected. If 

 

 

  it is, the M-227 will require that coolant be flowing or else it will create a fault. 

 

 

  If for some reason the Cooling Unit is connected but not being used the 

 

 

  operator can change the Coolant Fault Set Up to OFF and no coolant fault 

 

 

  will be detected. 

CAUTION 

 

 

 

Severe damage to the weld head and cables can occur if you have the Coolant Fault turned 

 

 

 

OFF and are operating a weld head that needs coolant and then you forget to turn the cooler 

 

 

 

on or to make the connections. 

 

 

   

3.  The above is the basic operation.  The only decision to be made is whether  

 

   

  COOLANT is required.  Some weld heads need it, some do not, depending  

 

   

    on the type of weld and duty  cycle.  Consult with an AMI representative as  

 

   

  to cooling requirements. 

 

 

8.2 

 

Summary of Contents for 227























































































Reviews:

No comments