manualshive.com logo in svg

AMI 227, Operation Manual, Page: 10 / 86

Share
Download
AMI 227 Operation Manual Download Page 10

 

 

MODEL 227 

OPERATION MANUAL

 

Doc # 740063 Rev E 

 

SECTION I - INTRODUCTION 

 

1.1 

SAFETY PRECAUTIONS 

 

WARNING

: Keep hands and fingers clear from moving parts 

such as fans, gears rotors, Wire Feed, Rotation and AVC 
Mechanisms. 

 

WARNING

: The M-227 Power Supply is not intended for 

pipe thawing or heating in any form. 

 

WARNING

: The M-227 Power Supply weighs in excess of 

91 lbs (41.3 kg).  It has no handles and is not intended to be 
carried by a single person. Be sure to follow your local, OSHA, 
international or employer guidelines for proper methods of 
lifting and re-locating this equipment. 

 
1.2 

OPERATIONAL PRECAUTIONS 

 

 

The following is a check list for operating personnel to follow to insure minimum 

            system down-time due to improper operation and handling: 

 

           1.   TOO AVOID severe equipment damage VERIFY that the M-227 is  
                  connected to the correct Input AC power (see section 3.1).  

  

           2.    Before operating, check all fittings and connectors for proper seating and that 
                  all protective boots are in place.  If not properly seated or protected, short 
                  circuits, poor connections or inert gas leaks could occur. 

 

 

3.   The M-227 is intended for typical GTAW gases ONLY. 

NEVER CONNECT 

                  OXYGEN OR ACETYLENE TO THE M-227. 

 

            4.   Before operating, insure that all cables are routed or protected in such a way 
                  that they will not be subject to heat, equipment and/or personnel traffic. Insure 
                  that the cables DO NOT come in contact with HOT PIPE.   

 

            5.   When storing or handling cables, always keep the protective boots and dust 
                  caps on all connectors and fittings until ready to install.  A major cause of 
                  downtime in any automatic welding system is improper care and use of cables. 

 

1.4

Summary of Contents for 227























































































Reviews:

No comments