manualshive.com logo in svg

AMI 227, Operation Manual, Page: 20 / 86

Share
Download
AMI 227 Operation Manual Download Page 20

 

 

MODEL 227 

OPERATION MANUAL

 

Doc # 740063 Rev E 

 

SECTION III - INSTALLATION 

 

3.1 

POWER CONNECTION 

 

 

2.  Install the AC line connector onto the power cord.  

 

NOTE 

  

     DO NOT PLUG THE M-227 INTO THE AC POWER SOURCE UNTIL 

 

     ALL INSTALLATION STEPS OF THIS MANUAL ARE COMPLETE. 

 
 

3.  Insure that the circuit breaker (CB-1) is in the OFF (down) position (see  

 

     figure 3). 

 
 

4.  Using figure 2 and 3 as a reference, locate the power SELECT SWITCH  

 

     (next to the input power connector).  The switch is concealed by a cover  

 

     plate and only the top of the switch handle can be seen through a hole in the  

 

     plate.  The plate is labeled as to what voltage it is currently set for. 

 
 

5.  If the M-227 is to be run on 100, 110, 115 or 120 VAC, this switch must be  

 

     in the 110 VAC position.  If it is to be run on 200, 208, 220, 230 or 240  

 

     VAC, it must be in the 220 VAC position. 

 
 

6.  To change the power select switch position, remove the cover retaining   

 

     screws (see figure 3) and remove the cover.  Set the switch to the alternate  

 

     position and install the cover plate.  It must be flipped over so the hole in the  

 

     plate will fit over the switch handle in the new position.  This will  

 

   

 

     automatically expose the alternate voltage label on the other side. 

 
3.2 

WELDING GAS CONNECTIONS 

 

 

1.  An Arc Input Gas Hose is supplied with the M-227.  This hose is made of  

 

     material selected specifically for automatic welding.  HOSES MADE    

 

     FROM OTHER MATERIAL ARE NOT RECOMMENDED (especially  

 

     rubber, nylon or tygon). 

 
 

2.  The 10 foot (3m) hose should be installed from the gas regulator/flowmeter  

 

     (user supplied) to the ARC GAS INPUT fittings required to mate with the  

 

     M-227 and most domestic (USA) inert gas flow meters. 

 

 

     The arc gas line is controlled by a solenoid and flow sensor in the M-227  

 

     and MUST BE connected to the M-227 (not directly to the weld head or  

 

     torch).  After installing the hose and fittings loosely by hand, tighten the 

 

     retaining nuts slightly with a wrench to insure there are no leaks, but do not 

 

     over-tighten.  The use of plumbers tape or grease is not recommended.

                                                                     

 

3.2

Summary of Contents for 227























































































Reviews:

No comments