manualshive.com logo in svg

AMI 227, Operation Manual, Page: 51 / 86

Share
Download
AMI 227 Operation Manual Download Page 51

 

 

MODEL 227 

OPERATION MANUAL

 

Doc # 740063 Rev E 

 

SECTION V - OPERATION 

 

5.6 

OVERRIDING FUNCTION VALUES 

 

 

4.  When the new value is displayed and verified, press the ENTER key.  The  

 

     function will stop blinking and the system is ready to change another value or  

 

     to operate. 

 

 

5.  MODES such as TIMER, ROT, etc. are not controlled by any limits and can be 

 

     changed overridden by the Operator by using the F key to change the MODE. 

 

5.7 

SET UP FUNCTIONS 

 

 

There are two types of SET UP screens. Both are accessed with the SET UP key.  

 

One type appears when the System Mode is set to Operate and both appear when   

 

The System Mode is set to OPERATE and both appear when the System Mode is  

 

set to PROGRAM. 

NOTE 

 

The SET UP screens offer special functions that can ENHANCE or in some cases 

 

CHANGE the way the M-227 operates. It is important for the user to understand 

 

these features. Under some conditions, if not properly set, undesirable performance 

 

can occur. 

 

 

1.  OPERATE MODE SET UP FUNCTIONS - Pressing the SET UP key on the 

 

     M-227 panel when on the STATUS SCREEN or WELD SCREEN with the 

 

     System Mode set to OPERATE will access the first of three SET UP screens 

 

     that contain the following functions:  

 

      

 

     1.  CALCULATE - Pressing the F key under this choice will access a prompt     

 

          screen for calculating Tungsten Length or RPM or Weld Time.  Follow the 

 

 

instruction on the screen to make these calculations.  These features can be 

 

 

very helpful when creating new weld procedures. 

 

 

 

     2.  WELD SELECT - This feature is used to select up to 4 different weld  

 

 

          schedules to be accessible by M-227-RP Remote Pendant.  Press the F key 

 

 

under Weld Select and follow the instructions on the display.  

 

 

     3.  COOLANT FAULT - If the Coolant Fault is ON the M-227 will look to see 

 

 

if an optional M227/207-CW or M207-CW Cooling Unit is connected.  If it is 

 

 

then the M-227will require that coolant be flowing or else it will create a fault. 

 

 

If for some reason the Cooling Unit is connected but not being used the 

                

operator can change this Coolant Fault Set Up to OFF and no coolant fault will 

 

 

be detected. 

 

CAUTION 

 

 

Severe damage to the weld head and cables can occur if you have the 

 

 

Coolant Fault turned OFF and are operating a weld head that needs 

 

 

coolant and then you forget to turn the cooler on or to make the connections. 

5.7 

 
 
 

Summary of Contents for 227























































































Reviews:

No comments