manualshive.com logo in svg

AMI 227, Operation Manual, Page: 57 / 86

Share
Download
AMI 227 Operation Manual Download Page 57

 

 

MODEL 227 

OPERATION MANUAL

 

Doc # 740063 Rev E 

 

SECTION V - OPERATION 

 

5.8 

REMOTE PENDANT (RP) OPERATION 

 

 

5. 

SPECIAL FUNCTION KEY

 - 

 

 

 

3.  

PRINT

 - Allows printing of Weld Pass from the RP .  Press the NEXT key 

 

 

 

to actuate the print function.  

 

 

 

4 

STORE

 - If the Operate Mode Key is in the PROGRAM position it is 

 

 

 

possible to permanently change some programmed values.  Accessing the 

 

 

 

STORE special function at the end of the sequence and pressing the NEXT 

 

 

 

key will permanently change the functions to the overridden values. 

 

 

 

5.  

SELECT

 - As previously noted, the M-227 can store in memory up to 100 

 

 

 

weld schedules .  Any 4 of these schedules can be programmed to be 

 

 

 

selected from the RP .  See Section 6 for information on how to set-up 

 

 

 

which Weld Schedules can be selected .  Pressing the NEXT key will 

 

 

 

replace the existing weld schedule in the SELECT function. 

 

 

 

6.  

PRE-WRAP

 - For use on M-95 series weld heads. Pressing the NEXT key 

 

 

    will engage the head Rotation and allow it to wrap the cable one time 

 

 

    before starting sequence. 

 

 

 

7.  

SET

 - Used in conjunction with a M-6 Weld Head to move the Torch to a  

 

 

 

pre-set arc gap prior to arc starting. 

 

 

 

8.  

OSC MAN

 - Used to engage the OSC function and perform the same 

 

 

 

movement out of sequence that it will perform in sequence.  Used to check 

 

 

 

Amplitude value. 

 

 

 

9. 

MAN ADV

 - For OVERRIDE purposes all weld schedule passes when 

 

 

 

called up from memory or reset after welding are said to be at Level 1 

 

 

 

values.  To Override a level 2 or greater function before welding requires 

 

 

 

the Operator to select this Special Function and use the Next key to 

 

 

 

Manually Advance to the desire LEVEL. 

 

CAUTION

   

 

If left in Level 02 or greater and Weld Sequence is started the system will start at  

 

Level 2 or greater. 

Unless this is the desired effect

 the user 

SHOULD ALWAYS

 

 

USE THE MAN ADV FUNCTION and PREV Key to return the system to 

 

Level 01 before Weld Sequence

. 

 

NOTE 

  

Except for PURGE, anytime a Special Function is actuated with the Next key it 

 

will do that function and then return to the 01 TEST display.  To repeat that 

 

special function (such as pass)  or to access another special function will require 

 

pressing the Special Function Key again. 

 

 

5.13 

Summary of Contents for 227























































































Reviews:

No comments