AMI 227 Operation Manual Download Page 41

Page: 41 / 86

MODEL 227

OPERATION MANUAL

Doc # 740063 Rev E

SECTION IV - SYSTEM FUNCTIONS

4.6

FAULTS

GAS FLT

- TORCH GAS FLOW is not detected. Fault creates an ALL

STOP if it occurs during a weld.

INPUT FLT -

If the M-227 cannot achieve desired outputs because of

inadequate AC input. Fault creates a SEQ STOP of it occurs during a weld.

SENSOR 1,2,3 -

User defined (see 4.7, 4.8 and 5.8).

BAD START -

Indicates that the system was unable to sustain an arc.

STUB OUT

- If the Arc Voltage gets too low or the electrode should touch

the puddle then a stub out will occur.

HIGH VOLTS -

If the Arc Voltage gets too high a fault will occur.

10.

GROUND FAULT -

On Heads with Ground Fault Sense, if the Work

Ground is not connected to the Work piece the system will detect this and

prevent arc start.

11.

OSC LIMIT

- On Heads with OSC limit switches, if they are engaged the

system will create an ALL STOP.

12.

AVC LIMIT

- On Heads with AVC limit switches, if they are engaged the

system will create an ALL STOP.

The method of alerting the operator depends on what the fault is and when it

occurs. A problem with TEMP, LVPS or INPUTAC when the M-227 is first

turned on will create a FAULT SCREEN and the fault must be corrected before

the M-227 will proceed with any other functions.

A problem with COOL, GAS or SENSOR is common at power on or when

preparing for welding. These items will only create the FAULT SCREEN if they

occur during weld sequence. BAD START appears only during weld sequence

(after pre-purge) and does not create a fault screen.

STUB OUT and HIGH VOLTS will only occur during a weld and will cause an

ALL STOP condition. After postpurge the normal “return to home” sequence will

also be disabled.

4.15

Summary of Contents for 227























































































Search results

Summary of Contents for 227

Reviews:

AMI 227, Operation Manual, Page: 41 / 86

Search results

Summary of Contents for 227

Reviews: