manualshive.com logo in svg

AMI 227, Operation Manual, Page: 77 / 86

Share
Download
AMI 227 Operation Manual Download Page 77

 

 

MODEL 227 

OPERATION MANUAL

 

Doc # 740063 Rev E 

 

SECTION VII - CALIBRATION 

 
7.5 

GENERAL MAINTENANCE INSTRUCTION 

    

   

WARNING        

 

 

   

Always disconnect the AC power cable from the line voltage before attempting to 

 

   

work with this welding power supply. 

 
 

1.   AIR FILTER - The M-227 power supply has one (1) foam air filter. Inspect this 

 

 

air filter regularly.  The foam filters may be washed in water and detergent, dried 

 

 

and reused or replaced.  Do not operate unit without filter in place. There is a  

 

 

similar filter on the M227/207-CW or M207-CW Cooling Unit that requires the

 

 

same inspection and cleaning. 

 
 

2.  COOLANT - The water tank in the optional M227/207-CW OR M207-CW unit 

 

 

holds approximately three (3) U.S. gallons. Check water level periodically.  Using 

 

 

different weld heads will remove water from tank over a period of time.  Fill the 

 

 

tank per instructions of Section VIII. 

 
 

3.    Cleaning exterior and interior surfaces - Prolonged use in dusty shop or outside  

 

    environments may cause the outside surfaces to accumulate a coating of dirt and  

 

    dust.  Do not use shop air (usually too wet) to blow dust particles away from  

 

    panels. Either wipe it off with a damp cloth or use a vacuum cleaner with a soft  

 

    brush .  Where a vacuum brush cannot reach, use clean, soft paint brush and then 

 

    vacuum. 

CAUTION

 

 

 

Always disconnect the power input cable from the junction box or wall-plug  

 

 

before cleaning. 

 
 

   

DO NOT USE ANY SOLVENTS, SPRAY-ON CLEANERS OR WATER

 on 

 

   

any of the inside parts.  All outside surfaces may be cleaned with a soft cloth or  

 

   

sponge, damp, NOT SOAKED, with a mild detergent solution. 

 

 

 

 

4.   INPUT/OUTPUT PANEL CONNECTIONS - Periodic inspection of the M-227  

 

 

 

panel and cable electrode, gas and water return quick-disconnects should be  

 

 

 

performed.  Damaged, dented or deformed connectors may cause poor or unsafe  

 

 

 

operation and water or gas leakage. 

 

 
 
 
 
 

 

7.7 

 
 

Summary of Contents for 227























































































Reviews:

No comments