manualshive.com logo in svg

AMI 227, Operation Manual, Page: 65 / 86

Share
Download
AMI 227 Operation Manual Download Page 65

 

 

MODEL 227 

OPERATION MANUAL

 

Doc # 740063 Rev E 

 

SECTION VI - PROGRAMMING 

 

6.1 

CREATE A WELD SCHEDULE  

 

 

2.  To CREATE a weld schedule press the F key below the word CREATE  

 

    and the following screen will appear: 

 

ENTER NEW WELD  #     -  THEN PRESS ENTER KEY 

PRESS C KEY TO CANCEL WELD PROGRAMMING 

 

  # 
000 

 

 

 

Enter the number using the numeric keys.  Look at the lower screen and  

 

 

confirm that the numbers entered are correct; if not, press CE and re-enter  

 

 

the numbers.  When correct, press the ENTER key.  If the number is already  

 

 

used the system will reject the number and ask the programmer to try again.  

 

 

3.  The description screen will appear when an acceptable weld schedule number 

 

 

has been entered:  

 

ENTER WELD  OD  -  THEN  PRESS THE ENTER KEY 

PRESS C KEY TO CANCEL PROGRAMMING MODE 

 

   #            OD           WALL          MAT                HEAD 
001         0.000            0.00            - - - - -              - - - - - 

NOTE  

 

 

The weld description and all values for LEVEL 1 of the weld schedule must be 

 

 

entered. They cannot be skipped, you must enter a number (even if it is 0) for 

 

 

each item before progressing to the next item. 

 

 

4.   Enter the O.D. (in inches or millimeters) using the numeric keys.  Verify the 

 

    correct number on the screen and then press the ENTER key.  

 

 

5.   After pressing the ENTER key follow the instructions on the screen for 

 

    entering the wall thickness. 

 

 

6.   The M-227 will then give you a choice of materials.  Use the F key to select 

 

    the proper one and Press Enter. 

 

 

7.   The M-227 will then give you a choice of Weld HEADS.  Use the F keys to 

 

    select the proper head, press ENTER. 

 

 

8.   Single Level functions will then appear: 

 

ENTER VALUE FOR BLINKING ITEM 

THEN PRESS ENTER KEY 

 

PRE-PURGE-POST  UP-SLOPE-DOWN  ROT--DLY 
000                   000 

00.0                 00.0 

CCW  00.0 

 

 

6.2 

Summary of Contents for 227























































































Reviews:

No comments