manualshive.com logo in svg

AMI 227, Operation Manual, Page: 31 / 86

Share
Download
AMI 227 Operation Manual Download Page 31

 

 

MODEL 227 

OPERATION MANUAL

 

Doc # 740063 Rev E 

 

SECTION IV - SYSTEM FUNCTIONS 

 

4.3 

WELD SEQUENCE 

 

 

3. 

EVENT 3: 

 

 

 

6.  WIRE FEED START DELAY - Feeding of the Wire should not occur,  

 

 

 

in most cases, until travel has started.  When the arc is established the  

 

 

 

WIRE FEED START DELAY time will begin to count.  When this time 

 

 

      is complete the wire will be able to feed if the Wire Mode is set to ON. 

 

 

 

7.   AVC START DELAY - The AVC should not be turned on until the 

                           current is near full value and the puddle has stabilized.  When the arc is 
 

 

      established the AVC START DELAY time will begin to count.  When 

 

 

 

this time is complete the AVC will be able to operate. 

 

 

 

8.  OSCILLATOR UPSLOPE - The Torch Oscillator Upslope is linked to 

 

 

 

the current Upslope time.  During the Current Upslope time the 

 

 

 

Oscillator Amplitude (movement) will start at 0 amplitude and slowly 

 

 

 

increase to the full program value of OSC Amplitude by the end of 

 

 

 

current Upslope. 

 

 

 

9.  OSCILLATOR DWELL and EXCURSION TIMERS - The Oscillator 

 

 

      movement is based on time.  The Level 1 Dwell and Excursion Timers 

 

 

 

start counting at the beginning of Event #3 (if OSC MODE is set to ON). 

 

 

4. 

EVENT 4:  FULL LEVEL FUNCTIONS - Sometime after the arc is   

 

 

established, depending on the weld schedule, the current UPSLOPE, OSC 

 

 

UPSLOPE and all START DELAYS (Travel, Wire, AVC) will be completed 

 

 

and all of the following functions will be in effect:   

 

 

 

1.  LEVEL 1 TIME - Will be counting towards 0.  During its count all of  

 

 

 

the below functions will be occurring: 

 

 

 

2.   LEVEL 1 PULSE MODE - The PULSE MODE can be set in each 

 

 

      LEVEL to work several different ways: 

 
 

 

       

ON =  In the ON mode system will pulse between PRIMARY and 

                            

BACKGROUND function values using the PULSE TIMERS for 

 

 

       

timing control. 

 
 

 

 

 

OFF =  In the OFF mode all system functions will be in 

 

 

 

 

PRIMARY only. No BACKGROUND functions will be done. 

 
 

 

 

 

SYNC = In the SYNC Mode the system will pulse between 

 

 

 

 

PRIMARY and BACKGROUND function values using the 

 

 

 

 

Oscillator Dwell and Excursion Timers for pulse control.   

 

4.5 

 

Summary of Contents for 227























































































Reviews:

No comments