manualshive.com logo in svg

American Dynamics RAS915LS, Operator'S Manual

Share
Download
American Dynamics RAS915LS Operator'S Manual Download Page 93

5.  Use the joystick to move the highlight to 

Presets

. Press 

Set

 to select. The 

Select Preset to 

Program

 screen displays. 

 

SELECT PRESET TO PROGRAM

 

PRESET

 

NUMBER PRESET 

NAME

 

1-64 PRESET 

1-64

 

FOCUS FAR to program preset

 

EXIT

 

 

6.  Use the joystick to select the Preset you want to program. If the Preset has been programmed the 

dome automatically moves to that position. 

• 

Move the joystick right to increase the preset number. 

• 

Move the joystick left to decrease the preset number. 

When the correct Preset number appears, press 

Set

 to begin programming. 

7. The 

Presets

 screen displays. Use the joystick to adjust the dome to the correct pan/tilt position. 

PRESETS

PRESET X

Position camera with PAN

TILT, ZOOM and IRIS

FOCUS FAR to save and exit

EXIT

 

IMPORTANT!

 If using the WV-CU550A Controller with the WJ-SX550 Multiplexer, you must 

press 

F3 (A. Res)

 to adjust the zoom, focus, or iris settings. This places the controller in normal 

navigating mode. Make the necessary adjustments.  When finished, press 

F1 (On)

 to resume 

menu mode. 

8. Press 

Set

 to save the Preset information. 

9.  To program more Presets, repeat steps 5 through 8. To exit the Dome Configuration Menu and 

save changes, press 

F4 (Exit)

. 

To verify the Preset programming, enter a Preset number (1-64) and press 

Preset

.  

Tested Panasonic Equipment 

The following Panasonic equipment has been tested with SpeedDome Ultra VII: 

• 

WJ-SX550 Multiplexer  

• 

WV-CU550A Controller 

 

Panasonic Up-the-Coax (UTC) Protocol Command Summary 

D–5 

Summary of Contents for RAS915LS





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands