manualshive.com logo in svg

American Dynamics RAS915LS, Operator'S Manual

Share
Download
American Dynamics RAS915LS Operator'S Manual Download Page 43

 

 

 

Note:

  

You will receive an error message under the following conditions:  

• 

If you attempt to program an area boundary that passes the starting point of the 
first area 

• 

If you move the camera left after establishing the first boundary 

Return to step 2 and start again. 

 

 

7.  When the last area boundary is set, save the changes. A message appears confirming that the areas 

have been successfully saved. Press 

Focus

 to continue. 

8. When 

the 

Alarms/Areas/Home/Presets/PZ 

screen appears, select 

Exit

. The 

Dome 

Configuration Menu

 appears. Continue with 

What To Do Next

 on page 4–20.  

Establishing Privacy Zones 

Privacy Zones

 are “masked” sections of the dome’s viewing area. These masks prevent operators of 

the surveillance system who do not have access to the dome password from viewing these designated 
zones. Each zone has four sides, and the zones may overlap to form irregular shapes. The Privacy 
Zones move in relation to the dome pan/tilt position. In addition, the apparent size of the Privacy 
Zone adjusts automatically as the zoom level is adjusted. Up to 

eight

 Privacy Zones may be 

established for a dome.  

Privacy Zones are useful for high security areas. For example, you might establish a Privacy Zone 
around a safe’s combination. However, you could view people approaching or opening the safe.  

When Privacy Zones are active, the dome's firmware automatically disables text transparency. For 
additional information about text appearance, see 

Chapter 5

.   

In addition, the appearance of the configuration menus changes slightly when Privacy Zones are 
active. Both the first and last lines of the menus will appear in enlarged text when Privacy Zones are 
active. The menus change to one-sized text if Privacy Zones are hidden or deleted. 

To program Privacy Zones, select 

Privacy Zones

 from the 

Alarms/Areas/Home/Presets/ PZ 

screen. The following screen appears: 

PRIVACY ZONES

ADD PRIVACY ZONES

DELETE SPECIFIC ZONE

DELETE ALL ZONES

HIDE ALL ZONES? NO/YES

EXIT

 

Configuring Alarms, Areas, Home, Privacy Settings, Presets, and Scan Limits 

4–11

 

Summary of Contents for RAS915LS





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands