American Dynamics RAS915LS Operator'S Manual Download Page 63

Page: 63 / 124

What To Do Next

When you select

Exit

from the

On-Screen Text Display

screen, the

Dome Configuration Menu

appears.

Figure 5-8: Dome Configuration Menu

DOME CONFIGURATION MENU

PAN/TILT/ZOOM/SYNC OPTS

CAMERA FUNCTIONS

ALARMS/AREAS/PRESETS/PZ

ON-SCREEN TEXT DISPLAY

LANGUAGE / PASSWORD

DOME INFORMATION

RESET TO FACTORY SETTINGS

QUIT WITHOUT SAVING

EXIT AND SAVE CHANGES

From this screen you can:

Chapter 2
Chapter 3
Chapter 4
Chapter 5

Chapter 7

Chapter 6

Chapter 1

•

Select an option to make additional changes.

•

Restore all settings to the factory defaults.

•

Exit the utility without saving changes.

•

Save the changes made and exit the utility.

Move the highlight bar to an item and select it. Refer to the related chapter for additional information.

Configuring Text Displayed On-Screen

5–11

Summary of Contents for RAS915LS





























































































































Search results

Summary of Contents for RAS915LS

Reviews:

Related manuals for RAS915LS

Brands by name

Popular brands

American Dynamics RAS915LS, Operator'S Manual

Search results

Summary of Contents for RAS915LS

Reviews:

Related manuals for RAS915LS

Brands by name

Popular brands