American Dynamics RAS915LS Operator'S Manual Download Page 109

Page: 109 / 124

DOME NUMBER: ___________________ LOCATION:

________________________

Area Boundaries

Up to 16 areas can be programmed. Use this form to identify the start and end points of each area. This will assist you in restoring the boundaries if the areas should be erased.

Area Number

Start Point

End Point

Area 1

Area 2

Area 3

Area 4

Area 5

Area 6

Area 7

Area 8

Area 9

Area 10

Area 11

Area 12

Area 13

Area 14

Area 15

Area 16

Privacy Zones

Up to eight Privacy Zones can be programmed. Use this form to identify the number of Privacy Zones programmed and areas being obscured.

Number

Description

Zone 1

Zone 2

Zone 3

Zone 4

Zone 5

Zone 6

Zone 7

Zone 8

Scan Limits

Scan Limit

Description

Left

Right

On-Screen Text Display

Menu Item

Default Setting (Choices)

Current Setting

Status Display

Off (On / Off)

Disable All Names

No (Yes / No)

Diagnostic Display

Off (On / Off)

Direction Indicator

Off (On / Off)

Text Attribute Options

Menu Item

Default Setting (Choices)

Current Setting

Character Outline

On (On / Off)

Translucent Names

On (On / Off)

Dome Configuration Records

R–3

Summary of Contents for RAS915LS





























































































































Search results

Summary of Contents for RAS915LS

Reviews:

Brands by name

Popular brands

American Dynamics RAS915LS, Operator'S Manual

Search results

Summary of Contents for RAS915LS

Reviews:

Brands by name

Popular brands