manualshive.com logo in svg

American Dynamics RAS915LS, Operator'S Manual

Share
Download
American Dynamics RAS915LS Operator'S Manual Download Page 17

Where To Go Next 

Now that you understand how to start and work with the Dome Configuration Utility, you are ready 
to begin changing the settings for your dome. Use the following chart to determine which chapters 
you should use next. 

Chapter 

Topics Covered 

Chapter 2: Configuring Pan, Tilt, 
Zoom, and Synchronization Options 

− 

Set the “flip” feature to rotate the dome 180° 

− 

Set the first zoom stop (22X or 33X) and maximum zoom (up 
to 242X) 

− 

Set line lock to prevent vertical rolling when switching 
between cameras 

Chapter 3: Configuring Camera 
Features 

− 

Enable automatic or manual White Balance settings (red and 
blue values) 

− 

Set the open shutter options to improve camera performance in 
low light situations  

− 

Enable automatic or manual Gain settings and set maximum 
gain values 

Chapter 4: Configuring Alarms, 
Areas, Home, Privacy Settings, Presets 
and Scan Limits 

− 

Set alarm actions to initiate a preset, pattern, or no action when 
alarm conditions are detected 

− 

Configure normal input states for alarms to be open or closed 

− 

Send input states to host controller 

− 

Set a “home” position for dome 

− 

Establish a North position for use with the direction indicators 

− 

Program Privacy Zones to prevent operators from viewing 
restricted areas 

− 

Program area boundaries 

− 

Program presets 

− 

Set scan limits 

Chapter 5: Configuring Text 
Displayed On-Screen 

− 

Display or hide dome status information 

− 

Display or hide camera, preset, pattern, area or alarm name 
information 

− 

Display diagnostic information or “splash” screen during dome 
reset 

− 

Display direction indicators 

− 

Assign names to camera, presets, patterns, areas, and alarms 

− 

Reset all names to factory defaults 

− 

Set text attributes (outline and translucent characters) 

Chapter 6: Configuring Language and 
Password Settings 

− 

Choose the language for the menus and prompts 

− 

Set a password to limit access to the Dome Configuration 
Utility 

− 

Enable or disable password protection 

Chapter 7: Displaying Dome 
Information  

− 

Display dome version information  

− 

Display dome performance statistics 

Using the Dome Configuration Utility 

1–7

 

Summary of Contents for RAS915LS





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands