manualshive.com logo in svg

Altuscn KM0032, User Manual, Page: 60 / 155

Share
Download
Altuscn KM0032 User Manual Download Page 60

KM0032 / KM0532 / KM0932 User Manual

48

Association

The Association page is used to associate a PN0108 PON (Power Over the 
NET™) power outlet with a KVM port on the Matrix KVM Switch. Once an 
association has been made, the power status of the device attached to the KVM 
port can be controlled from the Port Access page, rather than having to control 
the power status by opening a separate web session to the PN0108.

Note:

1. This page is only available through the Browser UI.

2. Use of this feature assumes you have installed a PN0108 and have 

connected it to a device attached to a KVM switch port on the 
installation, as shown in the diagram on page 133.

3. Visit our website for the latest PON firmware and up-to-date 

information about supported PON models.

Power Management

When you select 

Association

 on the menu bar, it opens to the Power 

Management page:

Summary of Contents for KM0032




























































































































































Reviews:

No comments